Hey Johnny,
I made some errors when submitting some nodes previously
9.15 should be TSTBD1, and 9.21 should be MELODY
Apologies, I've had to deal with moving node names around and it got a bit messy. ;)
--
Cory Smelosky
http://gewt.net/ Personal stuff!
http://gimme-sympathy.org/ My permanently-a-work-in-progress pet project.
On 28 Dec 2012, at 23:32, Dave McGuire <mcguire at neurotica.com> wrote:
On 12/28/2012 11:31 PM, Cory Smelosky wrote:
How loud is the 7720?
It's not quiet. ;) It makes a very low "rumble". It's
quite...comforting. =)
I'd expect a system like that to make a fitting sound. ;)
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
--
Cory Smelosky
http://gewt.net/ Personal stuff!
http://gimme-sympathy.org/ My permanently-a-work-in-progress pet project.
On 12/28/2012 11:31 PM, Cory Smelosky wrote:
How loud is the 7720?
It's not quiet. ;) It makes a very low "rumble". It's
quite...comforting. =)
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
On 28 Dec 2012, at 23:29, Dave McGuire <mcguire at neurotica.com> wrote:
On 12/28/2012 12:43 AM, Mark Wickens wrote:
61.6, BIGV7K
Vax 7720, 2GB RAM, HSJ50-based CI-connected disk arrays. VMS
v7.3. It will be online sporadically, but pretty much full-time for
now, to help heat the building until we get our natural gas feed
turned on. (no joke!)
Of course photographs of vaxen pron are always welcome ;)
I took some quick cell phone pics the other day for someone else who
asked. The lighting was poor and things weren't well-staged, but here
they are:
http://www.neurotica.com/misc/vax7000/
I'm sorry for the poor quality. I'll take proper pics when I get
things organized a bit in here.
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
How loud is the 7720?
--
Cory Smelosky
http://gewt.net/ Personal stuff!
http://gimme-sympathy.org/ My permanently-a-work-in-progress pet project.
On 12/28/2012 12:43 AM, Mark Wickens wrote:
61.6, BIGV7K
Vax 7720, 2GB RAM, HSJ50-based CI-connected disk arrays. VMS
v7.3. It will be online sporadically, but pretty much full-time for
now, to help heat the building until we get our natural gas feed
turned on. (no joke!)
Of course photographs of vaxen pron are always welcome ;)
I took some quick cell phone pics the other day for someone else who
asked. The lighting was poor and things weren't well-staged, but here
they are:
http://www.neurotica.com/misc/vax7000/
I'm sorry for the poor quality. I'll take proper pics when I get
things organized a bit in here.
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
On 28 Dec 2012, at 17:51, Cory Smelosky <b4 at gewt.net> wrote:
On 28 Dec 2012, at 17:48, "Rob Jarratt" <robert.jarratt at ntlworld.com> wrote:
-----Original Message-----
From: owner-hecnet at Update.UU.SE [mailto:owner-hecnet at Update.UU.SE]
On Behalf Of Cory Smelosky
Sent: 28 December 2012 20:41
To: hecnet at Update.UU.SE
Subject: Re: [HECnet] SIMH + Multiple interfaces + DECnet
On 28 Dec 2012, at 15:39, hvlems at zonnet.nl wrote:
No this is correct. What kind of hardware and os?
Is it on-line at Hecnet?
FreeBSD. XQB is attached to a tap0 device that is created by OpenVPN that
is bridged with my home network.
No. It is not currently on HECnet. It's going to become my area router.
[Rob Jarratt]
If you just need an area router, have you considered trying the user mode
router I wrote recently? It runs on Windows and on Raspberry Pi (Debian).
You will have to build it and it might need a tweak or two to run on
FreeBSD.
It doesn't need two NICs either, although your environment sounds a bit
different to anything I have tested so far.
Can it take packets from say: tap0 and route them out via a link on em0?
But you can just install another copy of multinet in a different
directory for each node and configure them separately.
Nonsense. Files in MULTINET_SPECIFIC_ROOT take
precedence over files in MULTINET_COMMON_ROOT.
I used to keep common clean, rename specific file to
common, configure it and renamed it back to specific.
--
Regards, Rok
Hi,
I looked into this a few years back and never found a solution. But you can just install another copy of multinet in a different directory for each node and configure them separately.
Dan
On 27 December 2012 21:58, <sampsa at mac.com> wrote:
I have a cluster with 3 nodes that have multinet on them.
Due to the stupidity of my router's forwarding rules, I need telnet to run on a different port on each of them, so eg:
NODE1 port 2301
NODE2 port 2302
NODE3 port 2303
Is this possible?
How do I configure this?
sampsa
