HECnet

hecnet@lists.dfupdate.se

15589 discussions

Re: Call to Action: Team is looking for contribution from OpenVMS and Open source community....

by ian＠platinum.net

On Oct 16, 2013, at 3:04 PM, Gregg Levine <gregg.drwho8 at gmail.com> wrote: Hello! And what were they discussing? Hopefully something important. Remember, at the moment HP has no idea exactly what VMS is and what it originally ran on, then what it took over, and its final platform. Did the email not make it to the list? Probably because it's an email thread with, for some unknown reason, the same email thread as a PDF attachment. If the email didnt make it to the list, let me know. (It may have got filtered because of the attachment that I didn't see at the time) Ian

12 years, 3 months

Re: [DECtec] Call to Action: Team is looking for contribution from OpenVMS and Open source community....

by b4＠gewt.net

On Wed, 16 Oct 2013, Ian McLaughlin wrote: Haha. After posting that email, I realized that they accidentally forwarded an entire conversation between two HP staffers discussing the email. I was a bit confused by the email when I got it, too. PR fail. Ian On Oct 16, 2013, at 2:58 PM, Ian McLaughlin <ian at platinum.net> wrote: Hello All, I just received the below email from HP. Did anyone else get it? It's quite interesting, but I'm also trying to figure out exactly where and when I told HP I was a VMS fan. I don't recall ever getting anything from HP in the past because of my hobbyist license registration. Wondering what others think about this - both from the 'HP reaching out' aspect as well as the aspect of promoting a port-it-to-VMS project. Ian -- Cory Smelosky http://gewt.net Personal stuff http://gimme-sympathy.org Projects

12 years, 3 months

Re: Call to Action: Team is looking for contribution from OpenVMS and Open source community....

by gregg.drwho8＠gmail.com

Hello! And what were they discussing? Hopefully something important. Remember, at the moment HP has no idea exactly what VMS is and what it originally ran on, then what it took over, and its final platform. ----- Gregg C Levine gregg.drwho8 at gmail.com "This signature fought the Time Wars, time and again." On Wed, Oct 16, 2013 at 6:01 PM, Ian McLaughlin <ian at platinum.net> wrote: Haha. After posting that email, I realized that they accidentally forwarded an entire conversation between two HP staffers discussing the email. PR fail. Ian On Oct 16, 2013, at 2:58 PM, Ian McLaughlin <ian at platinum.net> wrote: Hello All, I just received the below email from HP. Did anyone else get it? It's quite interesting, but I'm also trying to figure out exactly where and when I told HP I was a VMS fan. I don't recall ever getting anything from HP in the past because of my hobbyist license registration. Wondering what others think about this - both from the 'HP reaching out' aspect as well as the aspect of promoting a port-it-to-VMS project. Ian

12 years, 3 months

Re: Call to Action: Team is looking for contribution from OpenVMS and Open source community....

by ian＠platinum.net

Haha. After posting that email, I realized that they accidentally forwarded an entire conversation between two HP staffers discussing the email. PR fail. Ian On Oct 16, 2013, at 2:58 PM, Ian McLaughlin <ian at platinum.net> wrote: Hello All, I just received the below email from HP. Did anyone else get it? It's quite interesting, but I'm also trying to figure out exactly where and when I told HP I was a VMS fan. I don't recall ever getting anything from HP in the past because of my hobbyist license registration. Wondering what others think about this - both from the 'HP reaching out' aspect as well as the aspect of promoting a port-it-to-VMS project. Ian

12 years, 3 months

HECnet bridge on tru64

by sampsa＠mac.com

On 16 Oct 2013, at 19:31, Johnny Billquist <bqt at softjar.se> wrote: On 2013-10-16 18:00, Sampsa Laine wrote: On 16 Oct 2013, at 17:18, Johnny Billquist <bqt at softjar.se> wrote: On 2013-10-16 11:57, Mark Wickens wrote: I am also taking a solaris box im presuming thatthe bridge would compile Ok on that? I have no reason to suspect it shouldn't work. But only testing will tell. And the same here - you might need to tweak a thing or two in the source. Johnny This got me thinking, could just customize a Raspian distro to run the bridge. Download the image, put it on a SD card and boot. Change network settings and enter uplink details in bridge.conf. bridge runs automatically in a screen launched by init (respawned if killed, of course). Instant HECnet-in-a-box :) Yes, apart that there is absolutely no reason to involve screen here. Kick the bridge from init. I like being able to watch the debug output in screen, but that's just me. Sampsa

12 years, 3 months

HECnet bridge on Solaris 2.9

by mark＠wickensonline.co.uk

Well, I managed to get the bridge compiled up on Solaris with some minor makefile and include and library tweaks having compiled up the latest libpcap. I am using the opencsw archive for general unix software. If I run the bridge with debug on I get the following output: ./bridge 4711 Config filename: bridge.conf Adding router ''local''. 0001187c:-4206648 Adding router ''update''. 82ee1319:4711 Adding DECnet bridge local. Trying to match local Matching against: local Found match: local == local Adding DECnet bridge update. Trying to match update Matching against: local Matching against: update Found match: update == update Adding LAT bridge local. Trying to match local Matching against: local Found match: local == local Adding LAT bridge update. Trying to match update Matching against: local Matching against: update Found match: update == update Host table: 0: local 0.0.0.0:0 (Rx: 0 Tx: 0 (Drop rx: 0)) Active: 1 Throttle: 0(000) 1: update 130.238.19.25:4711 (Rx: 0 Tx: 0 (Drop rx: 0)) Active: 1 Throttle: 0(000) Hash of known destinations: Adding new hash entry. Port is 1 Adding new hash entry. Port is 1 Adding new hash entry. Port is 1 Adding new hash entry. Port is 1 Adding new hash entry. Port is 1 Adding new hash entry. Port is 1 Setting existing hash to bridge 1 Setting existing hash to bridge 1 Setting existing hash to bridge 1 Setting existing hash to bridge 1 Adding new hash entry. Port is 1 Setting existing hash to bridge 1 Setting existing hash to bridge 1 Adding new hash entry. Port is 1 Adding new hash entry. Port is 1 Which looks encouraging, but when I try and use DECNET on SLAVE I get the following: [MSW]SLAVE$ dir mim:: %DIRECT-E-OPENIN, error opening MIM::*.*;* as input -RMS-F-SYS, QIO system service request failed -SYSTEM-F-PATHLOST, path to network partner node lost Any ideas what might be going wrong? I've updated my NAT to point to the Ultra 5 for port 4711. Regards, Mark.

12 years, 3 months

HECnet bridge on tru64

by mark＠wickensonline.co.uk

Hehe! I didn't even mean to send that, not sure how it leaked out. Not autocorrect, that is me dictating a message. It works quite well except for punctuation. Not worked that one out yet full stop you know what I mean? ;) I bet emoticons are tricky as well I fully appreciate that not using a keyboard means I am an enigma amongst my peers... :D On 16/10/2013 17:27, Michael Young wrote: Autocorrect? :) On Oct 16, 2013, at 12:08 PM, Mark Wickens <mark at wickensonline.co.uk> wrote: good point samsung I'd forgotten that I had the bridge running on my raspberry pi so at least if nothing else I could sack in the laptop and take the pi instead however I'm going to see if I can't get it running on the sun. If that's the case we maybe want to make a list of the operating systems and versions for which the bridge has been successfully compiled. Sent from Samsung Mobile -------- Original message -------- From: Sampsa Laine <sampsa at mac.com> Date: 10/16/2013 5:00 PM (GMT+00:00) To: hecnet at Update.UU.SE Subject: Re: [HECnet] HECnet bridge on tru64 On 16 Oct 2013, at 17:18, Johnny Billquist <bqt at softjar.se> wrote: > On 2013-10-16 11:57, Mark Wickens wrote: >> I am also taking a solaris box im presuming thatthe bridge would compile >> Ok on that? > > I have no reason to suspect it shouldn't work. But only testing will tell. And the same here - you might need to tweak a thing or two in the source. > > Johnny This got me thinking, could just customize a Raspian distro to run the bridge. Download the image, put it on a SD card and boot. Change network settings and enter uplink details in bridge.conf. bridge runs automatically in a screen launched by init (respawned if killed, of course). Instant HECnet-in-a-box :) Michael Young young at ecn.purdue.edu -- http://www.wickensonline.co.uk http://hecnet.eu http://declegacy.org.uk http://retrochallenge.net https://twitter.com/#!/%40urbancamo

12 years, 3 months

HECnet bridge on tru64

by md.benson＠gmail.com

On 16 Oct 2013, at 17:00, Sampsa Laine <sampsa at mac.com> wrote: This got me thinking, could just customize a Raspian distro to run the bridge. Download the image, put it on a SD card and boot. Change network settings and enter uplink details in bridge.conf. bridge runs automatically in a screen launched by init (respawned if killed, of course). Instant HECnet-in-a-box :) That'd be neat. STAR69 runs on a Pi with Raspbian and bridge running out to HECnet so it's totally doable. If you could trim the distro down a bit (well, a lot actually) and make bridge run as a service it'd be neat. If you could get SimH to run as a service with a disconnectable terminal and optional between PDP-11 and VAX that'd be even neater. Maybe I went a little OTT on that one a SD card for bridge on a cut-down Pi linux would be a cool start though :) -- Mark Benson http://DECtec.info Twitter: @DECtecInfo HECnet: STAR69::MARK Online Resource & Mailing List for DEC Enthusiasts.

12 years, 3 months

HECnet bridge on tru64

by bqt＠softjar.se

On 2013-10-16 18:00, Sampsa Laine wrote: On 16 Oct 2013, at 17:18, Johnny Billquist <bqt at softjar.se> wrote: On 2013-10-16 11:57, Mark Wickens wrote: I am also taking a solaris box im presuming thatthe bridge would compile Ok on that? I have no reason to suspect it shouldn't work. But only testing will tell. And the same here - you might need to tweak a thing or two in the source. Johnny This got me thinking, could just customize a Raspian distro to run the bridge. Download the image, put it on a SD card and boot. Change network settings and enter uplink details in bridge.conf. bridge runs automatically in a screen launched by init (respawned if killed, of course). Instant HECnet-in-a-box :) Yes, apart that there is absolutely no reason to involve screen here. Kick the bridge from init. Johnny

12 years, 3 months

HECnet bridge on tru64

by jibanes＠gmail.com

Where can I find the hecnet bridge source code? On Wed, Oct 16, 2013 at 9:32 AM, Cory Smelosky <b4 at gewt.net> wrote: Sutocorrect here is fine with sampsa's name. HECnet-in-a-box is a neat concept...wouldn't be too hard to implement. Sent from my iPhone On 16 Oct 2013, at 12:28, "Michael Young" <young at ecn.purdue.edu> wrote: Autocorrect? :) On Oct 16, 2013, at 12:08 PM, Mark Wickens <mark at wickensonline.co.uk> wrote: good point samsung I'd forgotten that I had the bridge running on my raspberry pi so at least if nothing else I could sack in the laptop and take the pi instead however I'm going to see if I can't get it running on the sun. If that's the case we maybe want to make a list of the operating systems and versions for which the bridge has been successfully compiled. Sent from Samsung Mobile -------- Original message -------- From: Sampsa Laine <sampsa at mac.com> Date: 10/16/2013 5:00 PM (GMT+00:00) To: hecnet at Update.UU.SE Subject: Re: [HECnet] HECnet bridge on tru64 On 16 Oct 2013, at 17:18, Johnny Billquist <bqt at softjar.se> wrote: On 2013-10-16 11:57, Mark Wickens wrote: I am also taking a solaris box im presuming thatthe bridge would compile Ok on that? I have no reason to suspect it shouldn't work. But only testing will tell. And the same here - you might need to tweak a thing or two in the source. Johnny This got me thinking, could just customize a Raspian distro to run the bridge. Download the image, put it on a SD card and boot. Change network settings and enter uplink details in bridge.conf. bridge runs automatically in a screen launched by init (respawned if killed, of course). Instant HECnet-in-a-box :) Michael Young young at ecn.purdue.edu

12 years, 3 months

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

HECnet