HECnet

hecnet@lists.dfupdate.se

15562 discussions

by sampsa＠mac.com

It was in fact the switch on the console panel with the circle in/circle out that was in the wrong position (UP instead of DOWN). Here's a picture for future reference: http://i47.tinypic.com/2rm8v4i.jpg Sampsa On 14 Dec 2012, at 15:18, Jordi Guillaumes i Pons <jg at jordi.guillaumes.name> wrote: El 14/12/2012, a les 14:20, Kari Uusim ki <uusimaki at exdecfinland.org> va escriure: There is that (dot-circle) button which is called halt. It should be in the position where the dot is outside the circle. I have just checked my 3300. The two position switch is in the "dot out of circle" position. The three position switch is in the "arrow" (middle) position. If the uVAX asks for the console language at each boot and/or asks always for date/time, then the NVRAM/TOY backup battery is dead and has to be replaced. You can use standard rechargeable batteries and it is relatively easy to do (I managed to do it myself, and I'm quite clumsy with hardware :)). Jordi Guillaumes i Pons jg at jordi.guillaumes.name HECnet: BITXOV::JGUILLAUMES

12 years, 6 months

Re: ATTN: Johnny BQT - area 8 bridge IP change to 46.65.175.115

by sampsa＠mac.com

That would be Mark Benson and Peter Lothberg according to MIM::DECNET.TXT. Sampsa On 16 Dec 2012, at 10:38, sampsa at mac.com wrote: Yup, I can see the bridge is working again. Most of the MULTINET connections are up too, here's the current situation: Known Circuit Volatile Summary as of 16-DEC-2012 13:36:33 Circuit State Loopback Adjacent Name Routing Node QNA-0 on 4.248 (SIMVAX) QNA-0 1.15 (PONDUS) QNA-0 4.249 (SLAVE) QNA-0 2.1 (LEGATO) QNA-0 6.1 (STAR69) QNA-0 62.637 (CTAKAH) QNA-0 19.40 (SGC) QNA-0 1.13 (MIM) QNA-0 19.41 (SG1) TCP-0-2 on 2.1 (LEGATO) TCP-0-3 on 3.171 (NUK1C) TCP-0-6 on -starting TCP-0-7 on 7.60 (BITXOV) TCP-1-9 on 19.41 (SG1) TCP-4-7 on 47.556 (KUHAVX) TCP-5-9 on -starting So areas 6 and 59 need to update their IPs, whoever they are :) Sampsa On 16 Dec 2012, at 00:03, Johnny Billquist <bqt at softjar.se> wrote: On 2012-12-15 05:21, sampsa at mac.com wrote: Johnny, That's actually 46.65.175.116 - sorry And since I actually have a DNS name for you, it turned out all I had to do was to send a HUP signal... Johnny On 13 Dec 2012, at 15:15, sampsa at mac.com wrote: Johnny, Due to some ISP migration stuff, my bridge is now on 46.65.175.115. sampsa -- Johnny Billquist || "I'm on a bus || on a psychedelic trip email: bqt at softjar.se || Reading murder books pdp is alive! || tryin' to stay hip" - B. Idol

12 years, 6 months

Re: ATTN: Johnny BQT - area 8 bridge IP change to 46.65.175.115

by sampsa＠mac.com

Yup, I can see the bridge is working again. Most of the MULTINET connections are up too, here's the current situation: Known Circuit Volatile Summary as of 16-DEC-2012 13:36:33 Circuit State Loopback Adjacent Name Routing Node QNA-0 on 4.248 (SIMVAX) QNA-0 1.15 (PONDUS) QNA-0 4.249 (SLAVE) QNA-0 2.1 (LEGATO) QNA-0 6.1 (STAR69) QNA-0 62.637 (CTAKAH) QNA-0 19.40 (SGC) QNA-0 1.13 (MIM) QNA-0 19.41 (SG1) TCP-0-2 on 2.1 (LEGATO) TCP-0-3 on 3.171 (NUK1C) TCP-0-6 on -starting TCP-0-7 on 7.60 (BITXOV) TCP-1-9 on 19.41 (SG1) TCP-4-7 on 47.556 (KUHAVX) TCP-5-9 on -starting So areas 6 and 59 need to update their IPs, whoever they are :) Sampsa On 16 Dec 2012, at 00:03, Johnny Billquist <bqt at softjar.se> wrote: On 2012-12-15 05:21, sampsa at mac.com wrote: Johnny, That's actually 46.65.175.116 - sorry And since I actually have a DNS name for you, it turned out all I had to do was to send a HUP signal... Johnny On 13 Dec 2012, at 15:15, sampsa at mac.com wrote: Johnny, Due to some ISP migration stuff, my bridge is now on 46.65.175.115. sampsa -- Johnny Billquist || "I'm on a bus || on a psychedelic trip email: bqt at softjar.se || Reading murder books pdp is alive! || tryin' to stay hip" - B. Idol

12 years, 6 months

KLH10 on Raspberri Pi / Nodelist update

by bqt＠softjar.se

Hi. On 2012-12-03 10:24, Jordi Guillaumes i Pons wrote: Hello, Please add to the HECnet nodelist: 7.79 BITXT0 TOPS-20(PANDA) - KLH10 - Raspbery Pi Done. Johnny I am running this simulator in the same Pi which currently holds 5 more VMs. I will see if it keeps stable, and if it does I will run it permanently. Issues to solve - KLH10 does not idle in the Pi. I'll check the idler device code to see if I can guess what is happening. - I tried to give KLH10 its own bridge device, plugged into the rest of my network via VDE switches and plugs, but it does not work. I have lots of IPBLP bugchecks and IP networking is unusable (weird enough, DECNET and LAT seem to work). It works fine if I use the main host interface in non-exclusive mode (but then I don't get LAT). - KLH10 frontend can't load *.EXE files. - TOPS-10 does not run well. I used a x86 KLH to dump the load code in SAV format and then I can boot TOPS-10, but it hungs after a while. On the other hand, I'm thinking about building a blinkenlights device using the GPIO pins of the Rasp-pi basing it on the actual parallel port blinkenlights panel driven by the "lites" device... :) It could be another nice hobby project... Jordi Guillaumes i Pons jg at jordi.guillaumes.name HECnet: BITXOV::JGUILLAUMES -- Johnny Billquist || "I'm on a bus || on a psychedelic trip email: bqt at softjar.se || Reading murder books pdp is alive! || tryin' to stay hip" - B. Idol

12 years, 6 months

Re: ATTN: Johnny BQT - area 8 bridge IP change to 46.65.175.115

by bqt＠softjar.se

On 2012-12-15 05:21, sampsa at mac.com wrote: Johnny, That's actually 46.65.175.116 - sorry And since I actually have a DNS name for you, it turned out all I had to do was to send a HUP signal... Johnny On 13 Dec 2012, at 15:15, sampsa at mac.com wrote: Johnny, Due to some ISP migration stuff, my bridge is now on 46.65.175.115. sampsa -- Johnny Billquist || "I'm on a bus || on a psychedelic trip email: bqt at softjar.se || Reading murder books pdp is alive! || tryin' to stay hip" - B. Idol

12 years, 6 months

Re: ATTN: Johnny BQT - area 8 bridge IP change to 46.65.175.115

by bqt＠softjar.se

:-) I'll get to it tonight, when I plan on going over my mailbox for things that I should respond to... Johnny On 2012-12-15 05:21, sampsa at mac.com wrote: Johnny, That's actually 46.65.175.116 - sorry On 13 Dec 2012, at 15:15, sampsa at mac.com wrote: Johnny, Due to some ISP migration stuff, my bridge is now on 46.65.175.115. sampsa -- Johnny Billquist || "I'm on a bus || on a psychedelic trip email: bqt at softjar.se || Reading murder books pdp is alive! || tryin' to stay hip" - B. Idol

12 years, 7 months

Re: ATTN: Johnny BQT - area 8 bridge IP change to 46.65.175.115

by sampsa＠mac.com

Johnny, That's actually 46.65.175.116 - sorry On 13 Dec 2012, at 15:15, sampsa at mac.com wrote: Johnny, Due to some ISP migration stuff, my bridge is now on 46.65.175.115. sampsa

12 years, 7 months

unsuscribe

by bqt＠softjar.se

On 2012-12-15 01:25, Patrick Jankowiak wrote: unsuscribe Actually, you should send that to majordomo at update, and it should be "unsubscribe hecnet". :-) Johnny -- Johnny Billquist || "I'm on a bus || on a psychedelic trip email: bqt at softjar.se || Reading murder books pdp is alive! || tryin' to stay hip" - B. Idol

12 years, 7 months

Auto-booting a MicroVAX 3400

by jg＠jordi.guillaumes.name

El 14/12/2012, a les 14:20, Kari Uusim ki <uusimaki at exdecfinland.org> va escriure: There is that (dot-circle) button which is called halt. It should be in the position where the dot is outside the circle. I have just checked my 3300. The two position switch is in the "dot out of circle" position. The three position switch is in the "arrow" (middle) position. If the uVAX asks for the console language at each boot and/or asks always for date/time, then the NVRAM/TOY backup battery is dead and has to be replaced. You can use standard rechargeable batteries and it is relatively easy to do (I managed to do it myself, and I'm quite clumsy with hardware :)). Jordi Guillaumes i Pons jg at jordi.guillaumes.name HECnet: BITXOV::JGUILLAUMES

12 years, 7 months

Auto-booting a MicroVAX 3400

by HECNET＠beyondthepale.ie

Or CI clustering... :-) Or booting from any sort of shared disk on a SCSI or fibre (or other?) array controller or bus :-) Regards, Peter Coghlan

12 years, 7 months

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

HECnet