On 22 Dec 2012, at 03:07, Cory Smelosky <b4 at gewt.net> wrote:
On 22 Dec 2012, at 02:38, Cory Smelosky <b4 at gewt.net> wrote:
On 22 Dec 2012, at 02:36, G. <gerry77 at mail.com> wrote:
On Sat, 22 Dec 2012 01:14:27 -0500, you wrote:
% DSK:MONGEN.MIC will not be written
% File DSK:MONGEN.MIC already exists
This is self explanatory: MONGEN will not overwrite MONGEN.MIC if it's already
there... I think it's done to avoid losing config data. :)
.do monbld
?MICCOF Cannot open file MIC:MONBLD.MIC - in "DO" command
Have you created MONBLD.MIC as I wrote? It's a non standard file "invented" by
me and should contain all those commands I've listed in my other message. :)
Just re-read your message and noticed my error. ;)
Now i'm trying to figure out how to use the TOPS-10 editor. ;)
I'm used to EDT instead of TECO!
HTH,
G.
http://klh10.trailing-edge.com/twonky-a11120.tar is what I'm using. Can you point out obvious stuff I missed? ;)
Seems I'm in need of a reinstall due to not having setsrc or other essential stuff to build a monitor. ;)
(finding a complete tape set on bitsavers is hard no bootable KL tapes, KS can't do networking, and the KLAD10 sets are incomplete)
On 22 Dec 2012, at 21:41, Dennis Boone <drb at msu.edu> wrote:
I'm looking for basically all the compilers (Ada, C, C++, Basic, Cobol,
Fortran, Pascal etc).
This is one of those "how pathological do any of you feel today" sorts
of questions. I went looking to see what all I might have laying
around, and there are more languages than you might remember. Posting
this to gauge interest.
A 1993/5.5 era set has at least these oddballs in addition to the above:
ops5
apl
bliss-32
cobol generator
dibol
dsm
lisp
Which lisp?
pl/i (pre-kednos)
plus at least one or two variants for VAXELN. I'm sure I missed at
least one. No clue how any of them work on more recent VMS.
De
I'm looking for basically all the compilers (Ada, C, C++, Basic, Cobol,
Fortran, Pascal etc).
This is one of those "how pathological do any of you feel today" sorts
of questions. I went looking to see what all I might have laying
around, and there are more languages than you might remember. Posting
this to gauge interest.
A 1993/5.5 era set has at least these oddballs in addition to the above:
ops5
apl
bliss-32
cobol generator
dibol
dsm
lisp
pl/i (pre-kednos)
plus at least one or two variants for VAXELN. I'm sure I missed at
least one. No clue how any of them work on more recent VMS.
De
The DECSET kit is on KUHAVX::. I put it there earlier in the week.
-Steve
-----Original Message-----
From: owner-hecnet at Update.UU.SE
[mailto:owner-hecnet at Update.UU.SE] On Behalf Of sampsa at mac.com
Sent: Saturday, December 22, 2012 05:41
To: hecnet at Update.UU.SE
Subject: Re: [HECnet] VAX Compilers now on KUHAVX::
What _IS_ missing from there is DECset? Anyone have a VAX copy?
sampsa
On 22 Dec 2012, at 12:34, sampsa at mac.com wrote:
Download away, my good man.
Sampsa
On 22 Dec 2012, at 12:33, Jordi Guillaumes i Pons
<jg at jordi.guillaumes.name> wrote:
Al 22/12/12 11:28, En/na sampsa at mac.com ha escrit:
I managed to find some (not sure if out-of-date) compiler
kits on GORVAX:: and moved them to KUHAVX::
They can be found in KUHAVX::KAHUNA$:[DOWNLOADS] (which should be
world readable)
Thanks! My COBOL was a little bit outdated (it is from the 1998
SDL...)
On Dec 22, 2012, at 1:23 PM, Rob Jarratt wrote:
-----Original Message-----
From: owner-hecnet at Update.UU.SE [mailto:owner-hecnet at Update.UU.SE]
On Behalf Of Cory Smelosky
Sent: 22 December 2012 17:23
To: hecnet at Update.UU.SE
Subject: [HECnet] SIMH PDP-10 + Networking?
Is it at all possible to do networking in SIMH's PDP-10 emulator?
Turns out I need to reinstall TOPS-10. ;)
So I either need to:
1). Stage TOPS-10 in SIMH then move to KLH10's KS emulator (seems to
uses different disk format) 2). Install TOPS-10 directly in klh10 (How
would I
change tapes during runtime using KLH10?) 3). Not have networking. ;)
Is configuring networking in KLH10's KS emulation the same as using it's
KL
emulation? devdef nib et cetera?
Thanks!=
If anyone has any knowledge of getting networking running over a DMC11 on a
KS10 please let me know. I am just about to try adding the DMC11 to the KS10
emulation in SIMH. Unfortunately I fear this may not work. This is because I
have it on good authority that TOPS-10 may have a driver for the very
similar DMR11, but TOPS-20 does not have even that (or not directly anyway).
I have no knowledge of TOPS-10 and would need help to get things working
there.
FWIW, DMC and DMR are the same at the programmer level. They are somewhat different at the protocol level -- DMC uses an older version of DDCMP and has some bugs in that implementation, especially in the "high speed" (1 Mb/s) version. But those aren't visible to driver writers, though they matter if you do your own DDCMP protocol implementation.
paul
-----Original Message-----
From: owner-hecnet at Update.UU.SE [mailto:owner-hecnet at Update.UU.SE]
On Behalf Of Cory Smelosky
Sent: 22 December 2012 17:23
To: hecnet at Update.UU.SE
Subject: [HECnet] SIMH PDP-10 + Networking?
Is it at all possible to do networking in SIMH's PDP-10 emulator?
Turns out I need to reinstall TOPS-10. ;)
So I either need to:
1). Stage TOPS-10 in SIMH then move to KLH10's KS emulator (seems to
uses different disk format) 2). Install TOPS-10 directly in klh10 (How
would I
change tapes during runtime using KLH10?) 3). Not have networking. ;)
Is configuring networking in KLH10's KS emulation the same as using it's
KL
emulation? devdef nib et cetera?
Thanks!=
If anyone has any knowledge of getting networking running over a DMC11 on a
KS10 please let me know. I am just about to try adding the DMC11 to the KS10
emulation in SIMH. Unfortunately I fear this may not work. This is because I
have it on good authority that TOPS-10 may have a driver for the very
similar DMR11, but TOPS-20 does not have even that (or not directly anyway).
I have no knowledge of TOPS-10 and would need help to get things working
there.
Regards
Rob
Is it at all possible to do networking in SIMH's PDP-10 emulator?
Turns out I need to reinstall TOPS-10. ;)
So I either need to:
1). Stage TOPS-10 in SIMH then move to KLH10's KS emulator (seems to uses different disk format)
2). Install TOPS-10 directly in klh10 (How would I change tapes during runtime using KLH10?)
3). Not have networking. ;)
Is configuring networking in KLH10's KS emulation the same as using it's KL emulation? devdef nib et cetera?
Thanks!
On 2012-12-22 17:12, Dan Williams wrote:
Hi,
I picked up some new machines a few weeks ago and have finally had the
time to get them sorted. I got a Microvax 3400 and 2 4000/200's in the
slim chassis (Thanks Martin).
Unfortunately the Power supply has gone on one of the 4000's.
So I have some new nodes to add please Johnny:
51.6 VIGO Microvax 3400 VMS 7.3
51.7 LENNY 4000/200 VMS 7.3
Also I thought I join in and get a Pi, in as part of my cluster :
51.10 Ghost Raspberry pi. VMS 7.3
All registered.
Johnny
--
Johnny Billquist || "I'm on a bus
|| on a psychedelic trip
email: bqt at softjar.se || Reading murder books
pdp is alive! || tryin' to stay hip" - B. Idol
On 22 Dec 2012, at 11:12, sampsa at mac.com wrote:
All done, UNZIPs and VUPS.COM are there.
Sampsa
On 22 Dec 2012, at 18:08, Cory Smelosky <b4 at gewt.net> wrote:
On 22 Dec 2012, at 11:07, sampsa at mac.com wrote:
Good point, I'll upload all of them with relevant extensions.
VUPS.COM, too.
Sampsa
On 22 Dec 2012, at 18:05, Cory Smelosky <b4 at gewt.net> wrote:
On 22 Dec 2012, at 10:58, sampsa at mac.com wrote:
Gentlemen,
As some of you know, there's a bunch of stuff (including an AXP SPL) on RHESUS::[MEDIALIB].
I've decided to make this stuff web-accessible, with the entry page being http://rhesus.sampsa.com/medialib.start.html
That page includes some useful links to install images for new members etc.
I am also in the process of uploading the entire contents to my hosting provider as a mirror, I suggest that once this is complete (in about 40 hours or so) that HTTP users use the mirror as it will have far better transfer rates - the uplink from RHESUS is only 1.5 Mbps.
If you have any additional stuff you think should be on there, let me know, and I will copy it across.
Which version of unzip.exe is up there? Might want to have a binary for all 3 platforms. cURL might be nice too.
sampsa
Want another mirror?
I have a bunch of disk i'm not using on my VPS and plenty of bandwidth.
