Ok, I solved one problem. It was doing a minimal boot. However, when I do a normal boot it gets stuck waiting to mount dka200. I have a dka200 drive, but it's obviously not the one it was originally configured with.
Can anyone point me in the right direction as to how to reset the configuration? I don't have any install disks so my goal is to get a copy of the licence files and keep the installed programming languages. It would be nice to take a backup for prosperity, but not essential.
Daniel
Sent from my iPhone
I've been going round in circles trying to get UCX up and running. I have the AUI transceiver plugged into the back and it has a green light.
It's VMS 6.2. It has been configured at some point as it had some old gateway and BIND entries.
I run the config tool, and when I select 4 (interface) it says
"Warning - No Ethernet device found on system, ESP1"
and then aborts. When I show dev on console it shows a device EZA0: which a MAC address.
I've spent hours on this and are feeling discouraged!
Daniel
Sent from my iPhone
Hello all,
I am reviving this puzzle now that my network has undergone more restructuring. ;)
I can not for the life of me figure out why NCP isn't running. NETWOR shows the information it should, DECnet is operational as I can SET HOST to it yet NCP still tells me it isn't running?
Have I forgotten to start an obvious daemon?
--
Cory Smelosky
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
On 10/04/2013 08:14 PM, Michael Holmes wrote:
Will do..
You'd love it now since they've installed a ton of speed and red light cameras.
DC set the record for highest number of tickets written of any large US city.
Oh lovely. Bitch about my driving by putting up cameras that my tax
dollars pay for? Fuck that noise. I don't miss that place AT ALL.
(no offense intended of course)
It's the only reason DC govt has enough money to stay open with the federal govt shutdown.
That figures!
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
Will do..
You'd love it now since they've installed a ton of speed and red light cameras.
DC set the record for highest number of tickets written of any large US city.
It's the only reason DC govt has enough money to stay open with the federal govt shutdown.
Sent from my iPhone
On Oct 4, 2013, at 8:07 PM, "Dave McGuire" <mcguire at neurotica.com> wrote:
Ah, my old stompin' grounds. I've been pulled over and ticketed all over
that area. ;) I lived in Greenbelt, MD and later Laurel, MD.
Send me your shipping address in private mail.
-Dave
On 10/04/2013 08:06 PM, Michael Holmes wrote:
Alexandria, VA (metro DC).
Sent from my iPhone
On Oct 4, 2013, at 7:52 PM, "Dave McGuire" <mcguire at neurotica.com> wrote:
Where are you located?
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
On Oct 4, 2013, at 7:16 PM, Michael Holmes <mholmes10 at hotmail.com> wrote:
I have two VaxStation 3100's that I bought some time back but didn't have time to mess with until now.
Unlike my DEC 3000, the serial console is an MMJ port and not a DB9 serial port.
Does anyone have an excess or spare MMJ to DB9 adaptor, or know where I can purchase an inexpensive one?
I tired hooking up my multisync monitor I have hooked up to my DEC 3000, but I don't think the graphic card is set to a setting within the monitor's range, as nothing shows up.
Thanks in advance.
Mike
--
Dave McGuire, AK4HZ
New Kensington, PA
Ah, my old stompin' grounds. I've been pulled over and ticketed all over
that area. ;) I lived in Greenbelt, MD and later Laurel, MD.
Send me your shipping address in private mail.
-Dave
On 10/04/2013 08:06 PM, Michael Holmes wrote:
Alexandria, VA (metro DC).
Sent from my iPhone
On Oct 4, 2013, at 7:52 PM, "Dave McGuire" <mcguire at neurotica.com> wrote:
Where are you located?
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
On Oct 4, 2013, at 7:16 PM, Michael Holmes <mholmes10 at hotmail.com> wrote:
I have two VaxStation 3100's that I bought some time back but didn't have time to mess with until now.
Unlike my DEC 3000, the serial console is an MMJ port and not a DB9 serial port.
Does anyone have an excess or spare MMJ to DB9 adaptor, or know where I can purchase an inexpensive one?
I tired hooking up my multisync monitor I have hooked up to my DEC 3000, but I don't think the graphic card is set to a setting within the monitor's range, as nothing shows up.
Thanks in advance.
Mike
--
Dave McGuire, AK4HZ
New Kensington, PA
Alexandria, VA (metro DC).
Sent from my iPhone
On Oct 4, 2013, at 7:52 PM, "Dave McGuire" <mcguire at neurotica.com> wrote:
Where are you located?
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
On Oct 4, 2013, at 7:16 PM, Michael Holmes <mholmes10 at hotmail.com> wrote:
I have two VaxStation 3100's that I bought some time back but didn't have time to mess with until now.
Unlike my DEC 3000, the serial console is an MMJ port and not a DB9 serial port.
Does anyone have an excess or spare MMJ to DB9 adaptor, or know where I can purchase an inexpensive one?
I tired hooking up my multisync monitor I have hooked up to my DEC 3000, but I don't think the graphic card is set to a setting within the monitor's range, as nothing shows up.
Thanks in advance.
Mike
Where are you located?
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
On Oct 4, 2013, at 7:16 PM, Michael Holmes <mholmes10 at hotmail.com> wrote:
I have two VaxStation 3100's that I bought some time back but didn't have time to mess with until now.
Unlike my DEC 3000, the serial console is an MMJ port and not a DB9 serial port.
Does anyone have an excess or spare MMJ to DB9 adaptor, or know where I can purchase an inexpensive one?
I tired hooking up my multisync monitor I have hooked up to my DEC 3000, but I don't think the graphic card is set to a setting within the monitor's range, as nothing shows up.
Thanks in advance.
Mike
I have two VaxStation 3100's that I bought some time back but didn't have time to mess with until now.
Unlike my DEC 3000, the serial console is an MMJ port and not a DB9 serial port.
Does anyone have an excess or spare MMJ to DB9 adaptor, or know where I can purchase an inexpensive one?
I tired hooking up my multisync monitor I have hooked up to my DEC 3000, but I don't think the graphic card is set to a setting within the monitor's range, as nothing shows up.
Thanks in advance.
Mike
