On Sat, Jan 3, 2015 at 12:11 AM, Johnny Billquist <bqt at softjar.se> wrote:
I just checked some more. I can reach BENDER:: (12,2), so based on that, HUB:: would appear to run correctly.
(HUB:: is supposedly my next hop going to BENDER::)
BENDER:: seems to be running Phase V (I suspect), as I can't really speak NICE to it, but PHONE worked fine.
You are correct, BENDER:: is Phase V.
Not sure what the problem going to area 22 would be then...
Sometimes I have noticed dodgy routing. For a while there was a node on the network advertising bad routes to the 12 network. I think it was a Linux box doing it. I never figured out what was doing it as by the time I got home and started looking at it, everything seemed to work just fine :-)
Regards, Tim.
Think that the config below wouldn=E2=80=99t work s the decent node-type =
is routing-iv which is a L1 router?
My fault. If you talk to dimma in area 59 it should say;
decnet node-type area
-P
I just checked some more. I can reach BENDER:: (12,2), so based on that, HUB:: would appear to run correctly.
(HUB:: is supposedly my next hop going to BENDER::)
BENDER:: seems to be running Phase V (I suspect), as I can't really speak NICE to it, but PHONE worked fine.
Not sure what the problem going to area 22 would be then...
Johnny
On 2015-01-02 16:32, Mark Darvill wrote:
Hi Tim,
DECnet on this test system is just Decnet IV running on VMS 7.3.
I can t do a loop node to 12.1023 but not sure that would work anyway if
it is a cisco.
Also can t seem to get to 12.2. Have just rebooted 22.10 as SIMH may
have crashed.
Mark
On 2 Jan 2015, at 15:15, Tim Sneddon <tim at sneddon.id.au
<mailto:tim at sneddon.id.au>> wrote:
On Fri, Jan 2, 2015 at 6:16 PM, Mark Darvill<mark.darvill at mac.com
<mailto:mark.darvill at mac.com>>wrote:
HI,
I have been playing with my cisco router and a SIMH Vax over the
break.
from my router I can see the following neighbours
cmrtr01#show decnet nei
Net Node Interface MAC address Flags
0 12.1023 Tunnel57 0000.0000.0000 A
0 42.1022 Tunnel51 0000.0000.0000 A
0 61.1023 Tunnel53 0000.0000.0000 A
0 22.10 FastEthernet0/1 aa00.0400.0a58 V
and the following routes
cmrtr01#show decnet route
Area Cost Hops Next Hop to Node Expires Prio
*1 50 2 Tunnel51 -> 42.1022
*2 52 4 Tunnel51 -> 42.1022
*3 51 3 Tunnel51 -> 42.1022
*7 50 2 Tunnel51 -> 42.1022
*8 50 2 Tunnel51 -> 42.1022
*9 40 2 Tunnel57 -> 12.1023
*11 50 2 Tunnel51 -> 42.1022
*12 20 1 Tunnel57 -> 12.1023 44
64 A+
*18 51 3 Tunnel51 -> 42.1022
*19 50 2 Tunnel51 -> 42.1022
*22 0 0 (Local) -> 22.100
*23 40 2 Tunnel53 -> 61.1023
*28 50 2 Tunnel51 -> 42.1022
*33 51 3 Tunnel51 -> 42.1022
*39 51 3 Tunnel51 -> 42.1022
*42 20 1 Tunnel51 -> 42.1022 45
64 A+
*47 50 2 Tunnel51 -> 42.1022
*59 50 2 Tunnel51 -> 42.1022
*61 20 1 Tunnel53 -> 61.1023 38
64 A+
Node Cost Hops Next Hop to Node Expires Prio
*(Area) 0 0 (Local) -> 22.100
*22.10 4 1 FastEthernet0/1 -> 22.10 33
64 V
*22.100 0 0 (Local) -> 22.100
My SIMH Vax can see my router and has an adjacency. My node is
22.10 and router 22.100
Can anyone see area 22 as I don t seem to be able to communicate
elsewhere.
Hi Mark,
My network is 12, your Tunnel57 hooks into my router. From my router
I am able to ping 22.100, but I cannot reach 22.10. Are you able to
hit my router (12.1023) or my VAX (12.2)? Which version of DECnet are
you running on 22.10?
I am happy to help you figure out what might be going on.
Regards, Tim.
--
Johnny Billquist || "I'm on a bus
|| on a psychedelic trip
email: bqt at softjar.se || Reading murder books
pdp is alive! || tryin' to stay hip" - B. Idol
Tim,
Just discovered the ping decnet command in IOS
Can ping you 12.1023 and 12.2 from the router which is good; can ping 22.10 from the router which is also good; but for some reason i cannot connect from VAX (22.10) on FastEthernet0/1 to 12.2.
This must be a local issue.
Is there anything else I need to setup above what I have for FE0/1 and decnet on my router?
decnet routing 22.100
decnet node-type area
interface FastEthernet0/1
ip address 10.22.1.254 255.255.255.0
speed auto
full-duplex
lat enabled
decnet cost 4
and my tunnel to you which I don t think is the problem
interface Tunnel57
description HECnet tunnel for Tim Sneddon (Area 12) [Version:274]
no ip address
decnet cost 20
tunnel source FastEthernet0/1
tunnel destination 120.146.225.243
tunnel path-mtu-discovery
Mark
On 2 Jan 2015, at 15:32, Mark Darvill <mark.darvill at mac.com> wrote:
Hi Tim,
DECnet on this test system is just Decnet IV running on VMS 7.3.
I can t do a loop node to 12.1023 but not sure that would work anyway if it is a cisco.
Also can t seem to get to 12.2. Have just rebooted 22.10 as SIMH may have crashed.
Mark
On 2 Jan 2015, at 15:15, Tim Sneddon <tim at sneddon.id.au> wrote:
On Fri, Jan 2, 2015 at 6:16 PM, Mark Darvill <mark.darvill at mac.com> wrote:
HI,
I have been playing with my cisco router and a SIMH Vax over the break.
from my router I can see the following neighbours
cmrtr01#show decnet nei
Net Node Interface MAC address Flags
0 12.1023 Tunnel57 0000.0000.0000 A
0 42.1022 Tunnel51 0000.0000.0000 A
0 61.1023 Tunnel53 0000.0000.0000 A
0 22.10 FastEthernet0/1 aa00.0400.0a58 V
and the following routes
cmrtr01#show decnet route
Area Cost Hops Next Hop to Node Expires Prio
*1 50 2 Tunnel51 -> 42.1022
*2 52 4 Tunnel51 -> 42.1022
*3 51 3 Tunnel51 -> 42.1022
*7 50 2 Tunnel51 -> 42.1022
*8 50 2 Tunnel51 -> 42.1022
*9 40 2 Tunnel57 -> 12.1023
*11 50 2 Tunnel51 -> 42.1022
*12 20 1 Tunnel57 -> 12.1023 44 64 A+
*18 51 3 Tunnel51 -> 42.1022
*19 50 2 Tunnel51 -> 42.1022
*22 0 0 (Local) -> 22.100
*23 40 2 Tunnel53 -> 61.1023
*28 50 2 Tunnel51 -> 42.1022
*33 51 3 Tunnel51 -> 42.1022
*39 51 3 Tunnel51 -> 42.1022
*42 20 1 Tunnel51 -> 42.1022 45 64 A+
*47 50 2 Tunnel51 -> 42.1022
*59 50 2 Tunnel51 -> 42.1022
*61 20 1 Tunnel53 -> 61.1023 38 64 A+
Node Cost Hops Next Hop to Node Expires Prio
*(Area) 0 0 (Local) -> 22.100
*22.10 4 1 FastEthernet0/1 -> 22.10 33 64 V
*22.100 0 0 (Local) -> 22.100
My SIMH Vax can see my router and has an adjacency. My node is 22.10 and router 22.100
Can anyone see area 22 as I don t seem to be able to communicate elsewhere.
Hi Mark,
My network is 12, your Tunnel57 hooks into my router. From my router I am able to ping 22.100, but I cannot reach 22.10. Are you able to hit my router (12.1023) or my VAX (12.2)? Which version of DECnet are you running on 22.10?
I am happy to help you figure out what might be going on.
Regards, Tim.
Hi Peter,
Similar to the tunnel defs I have already that were pushed by Brian.
Think that the config below wouldn t work s the decent node-type is routing-iv which is a L1 router?
I am trying few things but I may take you up on the tunnel offer later.
Thanks, Mark
On 2 Jan 2015, at 15:36, Peter Lothberg <roll at Stupi.SE> wrote:
I'm happy to add a tunnel to Dimma if you would like to try that?
Config hints:
decnet routing 22.10
decnet node-type routing-iv
!
interface Tunnel4000
description tunnel to Stockholm 59.60
no ip address
decnet cost 10
tunnel source your-ip
tunnel destination 130.238.19.60
!
interface FastEthernet0/0
decnet cost 10
-P
Hi Paul,
VAX is a L1 router and cisco is an Area L2 router
I get an adjacency up between VAX and cisco when I bring the router up. I can see Area 22 from VAX with the next node to Area being 22.100, so things look OK locally.
The router must be using the tunnels to see neighbours.
Mark
On 2 Jan 2015, at 15:37, Paul_Koning at Dell.com wrote:
On Jan 2, 2015, at 5:16 AM, Mark Darvill <mark.darvill at mac.com> wrote:
HI,
I have been playing with my cisco router and a SIMH Vax over the break.
...
My SIMH Vax can see my router and has an adjacency. My node is 22.10 and router 22.100
What node type is your VAX? L1 router? What does it report as reachable? What events do you get when you bring up the connection to the router?
paul
On Jan 2, 2015, at 5:16 AM, Mark Darvill <mark.darvill at mac.com> wrote:
HI,
I have been playing with my cisco router and a SIMH Vax over the break.
...
My SIMH Vax can see my router and has an adjacency. My node is 22.10 and router 22.100
What node type is your VAX? L1 router? What does it report as reachable? What events do you get when you bring up the connection to the router?
paul
I'm happy to add a tunnel to Dimma if you would like to try that?
Config hints:
decnet routing 22.10
decnet node-type routing-iv
!
interface Tunnel4000
description tunnel to Stockholm 59.60
no ip address
decnet cost 10
tunnel source your-ip
tunnel destination 130.238.19.60
!
interface FastEthernet0/0
decnet cost 10
-P
Hi Tim,
DECnet on this test system is just Decnet IV running on VMS 7.3.
I can t do a loop node to 12.1023 but not sure that would work anyway if it is a cisco.
Also can t seem to get to 12.2. Have just rebooted 22.10 as SIMH may have crashed.
Mark
On 2 Jan 2015, at 15:15, Tim Sneddon <tim at sneddon.id.au> wrote:
On Fri, Jan 2, 2015 at 6:16 PM, Mark Darvill <mark.darvill at mac.com> wrote:
HI,
I have been playing with my cisco router and a SIMH Vax over the break.
from my router I can see the following neighbours
cmrtr01#show decnet nei
Net Node Interface MAC address Flags
0 12.1023 Tunnel57 0000.0000.0000 A
0 42.1022 Tunnel51 0000.0000.0000 A
0 61.1023 Tunnel53 0000.0000.0000 A
0 22.10 FastEthernet0/1 aa00.0400.0a58 V
and the following routes
cmrtr01#show decnet route
Area Cost Hops Next Hop to Node Expires Prio
*1 50 2 Tunnel51 -> 42.1022
*2 52 4 Tunnel51 -> 42.1022
*3 51 3 Tunnel51 -> 42.1022
*7 50 2 Tunnel51 -> 42.1022
*8 50 2 Tunnel51 -> 42.1022
*9 40 2 Tunnel57 -> 12.1023
*11 50 2 Tunnel51 -> 42.1022
*12 20 1 Tunnel57 -> 12.1023 44 64 A+
*18 51 3 Tunnel51 -> 42.1022
*19 50 2 Tunnel51 -> 42.1022
*22 0 0 (Local) -> 22.100
*23 40 2 Tunnel53 -> 61.1023
*28 50 2 Tunnel51 -> 42.1022
*33 51 3 Tunnel51 -> 42.1022
*39 51 3 Tunnel51 -> 42.1022
*42 20 1 Tunnel51 -> 42.1022 45 64 A+
*47 50 2 Tunnel51 -> 42.1022
*59 50 2 Tunnel51 -> 42.1022
*61 20 1 Tunnel53 -> 61.1023 38 64 A+
Node Cost Hops Next Hop to Node Expires Prio
*(Area) 0 0 (Local) -> 22.100
*22.10 4 1 FastEthernet0/1 -> 22.10 33 64 V
*22.100 0 0 (Local) -> 22.100
My SIMH Vax can see my router and has an adjacency. My node is 22.10 and router 22.100
Can anyone see area 22 as I don t seem to be able to communicate elsewhere.
Hi Mark,
My network is 12, your Tunnel57 hooks into my router. From my router I am able to ping 22.100, but I cannot reach 22.10. Are you able to hit my router (12.1023) or my VAX (12.2)? Which version of DECnet are you running on 22.10?
I am happy to help you figure out what might be going on.
Regards, Tim.
On Fri, Jan 2, 2015 at 6:16 PM, Mark Darvill <mark.darvill at mac.com> wrote:
HI,
I have been playing with my cisco router and a SIMH Vax over the break.
from my router I can see the following neighbours
cmrtr01#show decnet nei
Net Node Interface MAC address Flags
0 12.1023 Tunnel57 0000.0000.0000 A
0 42.1022 Tunnel51 0000.0000.0000 A
0 61.1023 Tunnel53 0000.0000.0000 A
0 22.10 FastEthernet0/1 aa00.0400.0a58 V
and the following routes
cmrtr01#show decnet route
Area Cost Hops Next Hop to Node Expires Prio
*1 50 2 Tunnel51 -> 42.1022
*2 52 4 Tunnel51 -> 42.1022
*3 51 3 Tunnel51 -> 42.1022
*7 50 2 Tunnel51 -> 42.1022
*8 50 2 Tunnel51 -> 42.1022
*9 40 2 Tunnel57 -> 12.1023
*11 50 2 Tunnel51 -> 42.1022
*12 20 1 Tunnel57 -> 12.1023 44 64 A+
*18 51 3 Tunnel51 -> 42.1022
*19 50 2 Tunnel51 -> 42.1022
*22 0 0 (Local) -> 22.100
*23 40 2 Tunnel53 -> 61.1023
*28 50 2 Tunnel51 -> 42.1022
*33 51 3 Tunnel51 -> 42.1022
*39 51 3 Tunnel51 -> 42.1022
*42 20 1 Tunnel51 -> 42.1022 45 64 A+
*47 50 2 Tunnel51 -> 42.1022
*59 50 2 Tunnel51 -> 42.1022
*61 20 1 Tunnel53 -> 61.1023 38 64 A+
Node Cost Hops Next Hop to Node Expires Prio
*(Area) 0 0 (Local) -> 22.100
*22.10 4 1 FastEthernet0/1 -> 22.10 33 64 V
*22.100 0 0 (Local) -> 22.100
My SIMH Vax can see my router and has an adjacency. My node is 22.10 and router 22.100
Can anyone see area 22 as I don t seem to be able to communicate elsewhere.
Hi Mark,
My network is 12, your Tunnel57 hooks into my router. From my router I am able to ping 22.100, but I cannot reach 22.10. Are you able to hit my router (12.1023) or my VAX (12.2)? Which version of DECnet are you running on 22.10?
I am happy to help you figure out what might be going on.
Regards, Tim.
