HECnet

hecnet@lists.dfupdate.se

15589 discussions

Downloading software to a DECSERVER 200 over MOP?

by sampsa＠mac.com

It's a 200. I'd need the mumble.SYS too. Sampsa On 14 Aug 2011, at 13:29, hvlems at zonnet.nl wrote: What kind of decserver is it? If it is a DS100, 200 or 300 then you need the appropriate load file mumble.SYS and a boot host that runs decnet. For NCP I can give you the incantations. Hans ------Origineel bericht------ Van: Sampsa Laine Afzender: owner-hecnet at Update.UU.SE Aan: hecnet at Update.UU.SE Beantwoorden: hecnet at Update.UU.SE Onderwerp: [HECnet] Downloading software to a DECSERVER 200 over MOP? Verzonden: 14 augustus 2011 14:15 Guys, Back for ages my DECSERVER used to boot up using someone's MOP box in Sweden I believe; This is no longer the case, and this being my only console access to RHESUS i would appreciate some instructions on how to set up this soft-downline-loading setup (and possibly the necessary binaries). Sampsa Verzonden vanaf mijn draadloze BlackBerry -toestel

14 years, 5 months

Downloading software to a DECSERVER 200 over MOP?

by hvlems＠zonnet.nl

What kind of decserver is it? If it is a DS100, 200 or 300 then you need the appropriate load file mumble.SYS and a boot host that runs decnet. For NCP I can give you the incantations. Hans ------Origineel bericht------ Van: Sampsa Laine Afzender: owner-hecnet at Update.UU.SE Aan: hecnet at Update.UU.SE Beantwoorden: hecnet at Update.UU.SE Onderwerp: [HECnet] Downloading software to a DECSERVER 200 over MOP? Verzonden: 14 augustus 2011 14:15 Guys, Back for ages my DECSERVER used to boot up using someone's MOP box in Sweden I believe; This is no longer the case, and this being my only console access to RHESUS i would appreciate some instructions on how to set up this soft-downline-loading setup (and possibly the necessary binaries). Sampsa Verzonden vanaf mijn draadloze BlackBerry -toestel

14 years, 5 months

Downloading software to a DECSERVER 200 over MOP?

by sampsa＠mac.com

Guys, Back for ages my DECSERVER used to boot up using someone's MOP box in Sweden I believe; This is no longer the case, and this being my only console access to RHESUS i would appreciate some instructions on how to set up this soft-downline-loading setup (and possibly the necessary binaries). Sampsa

14 years, 5 months

Weird question: Does anybody chow the external IP address on GORVAX?

by bob＠jfcl.com

188.220.63.6 is what I have. Bob -----Original Message----- From: owner-hecnet at Update.UU.SE [mailto:owner-hecnet at Update.UU.SE] On Behalf Of Sampsa Laine Sent: Saturday, August 13, 2011 6:38 PM To: hecnet at Update.UU.SE Subject: [HECnet] Weird question: Does anybody chow the external IP address on GORVAX? Had to replace my router today and lost a lot of port forwarding data with it. Anyway, if anyone who regularly connects to GORVAX (say for multinet), I would appreciate the info Samosa

14 years, 5 months

Weird question: Does anybody chow the external IP address on GORVAX?

by sampsa＠mac.com

Had to replace my router today and lost a lot of port forwarding data with it. Anyway, if anyone who regularly connects to GORVAX (say for multinet), I would appreciate the info Samosa

14 years, 5 months

new systems

by hvlems＠zonnet.nl

Hi, Area 44 has grown two new nodes: 44.43. OZON. (DS10 / VMS 8.3) 44.35 TITAAN (DS20E / VMS 8.3) Hans Verzonden vanaf mijn draadloze BlackBerry -toestel

14 years, 6 months

TOPS20 on simh

by jferraro＠gmail.com

Bob, I've have had no luck with idle on either simh or klh10 (for TOPS20). I'd planned to post to alt.sys.pdp10 but hadn't gotten around to it yet. If you run across anything, I'd be interested. I may experiment a bit this weekend if I get the time. Joe On Thu, Aug 4, 2011 at 5:29 PM, Bob Armstrong <bob at jfcl.com> wrote: Are there any HECnet'ers running TOPS20 on simh? Have you gotten the idle detection to work? I set up a TOPS20 system with simh (simh v3.8.1 on Ubuntu, TOPS20 v4.1 clean install). The installation went fine with no problems, but I cannot get the idle detection feature in simh to work. I say - pdp10 sim> att rp0 tops20-4.1.rp06 sim> set cpu tops20 sim> set cpu idle tops20 sim> show cpu CPU, idle enabled, stability wait = 20s, 1048KW, TOPS-20 sim> b rp .... Everything boots and runs fine, but simh uses about 98% of the host CPU and never goes down. In an hour of wall clock time the pdp10 process uses about 58+ minutes of CPU time. Clearly the idle detection isn't working for me. I did try posting this question on the simh list, but got no comments so I guess nobody there is using TOPS20. And yes, I could use KLH10, but AFAIK KLH10 has no idle detection feature at all. Thanks, Bob

14 years, 6 months

TOPS20 on simh

by hvlems＠zonnet.nl

Bob, perhaps posting on alt.sys.pdp10 may help. Hans ------Origineel bericht------ Van: Bob Armstrong Afzender: owner-hecnet at Update.UU.SE Aan: hecnet at Update.UU.SE Beantwoorden: hecnet at Update.UU.SE Onderwerp: [HECnet] TOPS20 on simh Verzonden: 4 augustus 2011 23:29 Are there any HECnet'ers running TOPS20 on simh? Have you gotten the idle detection to work? I set up a TOPS20 system with simh (simh v3.8.1 on Ubuntu, TOPS20 v4.1 clean install). The installation went fine with no problems, but I cannot get the idle detection feature in simh to work. I say - pdp10 sim> att rp0 tops20-4.1.rp06 sim> set cpu tops20 sim> set cpu idle tops20 sim> show cpu CPU, idle enabled, stability wait = 20s, 1048KW, TOPS-20 sim> b rp .... Everything boots and runs fine, but simh uses about 98% of the host CPU and never goes down. In an hour of wall clock time the pdp10 process uses about 58+ minutes of CPU time. Clearly the idle detection isn't working for me. I did try posting this question on the simh list, but got no comments so I guess nobody there is using TOPS20. And yes, I could use KLH10, but AFAIK KLH10 has no idle detection feature at all. Thanks, Bob Verzonden vanaf mijn draadloze BlackBerry -toestel

14 years, 6 months

TOPS20 on simh

by bob＠jfcl.com

Are there any HECnet'ers running TOPS20 on simh? Have you gotten the idle detection to work? I set up a TOPS20 system with simh (simh v3.8.1 on Ubuntu, TOPS20 v4.1 clean install). The installation went fine with no problems, but I cannot get the idle detection feature in simh to work. I say - pdp10 sim> att rp0 tops20-4.1.rp06 sim> set cpu tops20 sim> set cpu idle tops20 sim> show cpu CPU, idle enabled, stability wait = 20s, 1048KW, TOPS-20 sim> b rp .... Everything boots and runs fine, but simh uses about 98% of the host CPU and never goes down. In an hour of wall clock time the pdp10 process uses about 58+ minutes of CPU time. Clearly the idle detection isn't working for me. I did try posting this question on the simh list, but got no comments so I guess nobody there is using TOPS20. And yes, I could use KLH10, but AFAIK KLH10 has no idle detection feature at all. Thanks, Bob

14 years, 6 months

SIMH networking in OS X 10.6?

by sampsa＠mac.com

Guys, Being that my Mini is starting to show its age, I figured I'd move GORVAX onto something more modern. Unfortunately that means running OS X 10.6 Snow Leopard - which means the networking went to shit. Anyone got a copy of the SIMH VAX binary to run properly on 10.6? Sampsa

14 years, 6 months

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

HECnet