At 2:42 PM -0400 23/5/14, Cory Smelosky wrote:
Is it possible to have SYSGEN do an autoconfigure again?
If you run it from the beginning (not using saved answers), yes.
--
Jean-Yves Bernier
On Fri, 23 May 2014, Cory Smelosky wrote:
Is it possible to have SYSGEN do an autoconfigure again? I'd love to not have to rely on my incorrect answers. ;)
--
Cory Smelosky
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
On Fri, 23 May 2014, Dave McGuire wrote:
WOOHOO!! Great work, man!
Thanks!
Next I'm going to pop in a DHV11 and re-SYSGEN.
-Dave
On 05/23/2014 02:06 PM, Cory Smelosky wrote:
On Fri, 23 May 2014, Cory Smelosky wrote:
I did it!
3 x 64kbit x 1 DRAM chips bad, disabled half the board:
boot [1,54]rsx11m
XDT: 66
XDT>g
RSX-11M-PLUS V4.3 BL66
sav /wb
RSX-11M-PLUS V4.3 BL66 256.KW System:"MINDY "
RED DU:=SY:
RED DU:=LB:
RED DU:=SP:
MOU DU:"RSX11MPBL66"
@DU:[1,2]STARTUP
A lot of my problem was XDT user error. Whoops.
--
Cory Smelosky
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
WOOHOO!! Great work, man!
-Dave
On 05/23/2014 02:06 PM, Cory Smelosky wrote:
On Fri, 23 May 2014, Cory Smelosky wrote:
I did it!
3 x 64kbit x 1 DRAM chips bad, disabled half the board:
boot [1,54]rsx11m
XDT: 66
XDT>g
RSX-11M-PLUS V4.3 BL66
sav /wb
RSX-11M-PLUS V4.3 BL66 256.KW System:"MINDY "
RED DU:=SY:
RED DU:=LB:
RED DU:=SP:
MOU DU:"RSX11MPBL66"
@DU:[1,2]STARTUP
A lot of my problem was XDT user error. Whoops.
--
Dave McGuire, AK4HZ
New Kensington, PA
On Fri, 23 May 2014, Cory Smelosky wrote:
I did it!
3 x 64kbit x 1 DRAM chips bad, disabled half the board:
boot [1,54]rsx11m
XDT: 66
XDT>g
RSX-11M-PLUS V4.3 BL66
sav /wb
RSX-11M-PLUS V4.3 BL66 256.KW System:"MINDY "
RED DU:=SY:
RED DU:=LB:
RED DU:=SP:
MOU DU:"RSX11MPBL66"
@DU:[1,2]STARTUP
A lot of my problem was XDT user error. Whoops.
--
Cory Smelosky
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
Cleaning the board had no effect. Went back to the other one.
I identified a failing row of chips and tried swapping some around bit after awhile anything above 128KW became glitchy. (I'll clean contacts tomorrow)
Also...it seems I had a bad DELQA on the bus which probably wasn't helping.
Sent from mobile device that advertises itself for no good reason
On 22 May 2014, at 09:33, Cory Smelosky <b4 at gewt.net> wrote:
On Thu, 22 May 2014, Johnny Billquist wrote:
On 2014-05-22 15:06, Cory Smelosky wrote:
On Thu, 22 May 2014, Johnny Billquist wrote:
:-)
So, what is the status now? It don't work?
DMA works fine! However other tests and SCSI FIFO does not.
Hmm. Ok.
I assume you have CPU in slot 1, and memory in slot 2. Slot 3 is also Q/CD,
Yeah.
and after that (if I remember right) you have Q/Q slots. Have you tried minimizing the config to just the minimum required to test the machine?
Yeah. I also wiped down the board a bit...it gave ECC errors before even doing memory access this time.
Putting the project on hold until the board dries. (It's the board i'm 98% sure, the behaviour is different enough to not indicate any other boards. Either it'll work after this...or it'll look really damn clean!)
Johnny
--
Cory Smelosky
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
On Thu, 22 May 2014, Johnny Billquist wrote:
On 2014-05-22 15:06, Cory Smelosky wrote:
On Thu, 22 May 2014, Johnny Billquist wrote:
:-)
So, what is the status now? It don't work?
DMA works fine! However other tests and SCSI FIFO does not.
Hmm. Ok.
I assume you have CPU in slot 1, and memory in slot 2. Slot 3 is also Q/CD,
Yeah.
and after that (if I remember right) you have Q/Q slots. Have you tried minimizing the config to just the minimum required to test the machine?
Yeah. I also wiped down the board a bit...it gave ECC errors before even doing memory access this time.
Putting the project on hold until the board dries. (It's the board i'm 98% sure, the behaviour is different enough to not indicate any other boards. Either it'll work after this...or it'll look really damn clean!)
Johnny
--
Cory Smelosky
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
On 2014-05-22 15:06, Cory Smelosky wrote:
On Thu, 22 May 2014, Johnny Billquist wrote:
:-)
So, what is the status now? It don't work?
DMA works fine! However other tests and SCSI FIFO does not.
Hmm. Ok.
I assume you have CPU in slot 1, and memory in slot 2. Slot 3 is also Q/CD, and after that (if I remember right) you have Q/Q slots. Have you tried minimizing the config to just the minimum required to test the machine?
Johnny
