18 Nov
2021
18 Nov
'21
1:16 a.m.
Been awhile since I've posted anything, or been connected but I'd like to
work on getting reconnected to HECnet.
I would still like to do Cisco connections - just need to pass that
through the firewall. Can a more-modern ISR running IOS-XE do DECnet?
(specifically a cisco 4321). Worst case I can just re-use the 2851, but
that's got a lot of telephony config on it so would like to separate out
uses if possible.
(Also - you may have previously known me as Cory Smelosky - please update
contact details and whatnot)
I used to be area 9 - I will continue to use that area.
Thanks!
--
Madeline Autumn-Rose
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
18 Nov
18 Nov
1:26 a.m.
Someone else will need to answer the question about various Cisco
capabilities.
Can't even remember where you were hooked up to before, and we we should
resume that or find some other alternative.
Johnny
On 2021-11-18 01:16, Madeline Autumn-Rose wrote:
Been awhile since I've posted anything, or been
connected but I'd like
to work on getting reconnected to HECnet.
I would still like to do Cisco connections - just need to pass that
through the firewall. Can a more-modern ISR running IOS-XE do DECnet?
(specifically a cisco 4321). Worst case I can just re-use the 2851, but
that's got a lot of telephony config on it so would like to separate out
uses if possible.
(Also - you may have previously known me as Cory Smelosky - please
update contact details and whatnot)
I used to be area 9 - I will continue to use that area.
Thanks!
--
Johnny Billquist || "I'm on a bus
|| on a psychedelic trip
email: bqt at softjar.se || Reading murder books
pdp is alive! || tryin' to stay hip" - B. Idol
1:38 a.m.
On Thu, 18 Nov 2021, Johnny Billquist wrote:
Someone else will need to answer the question about
various Cisco
capabilities.
Can't even remember where you were hooked up to before, and we we should
resume that or find some other alternative.
I was previously part of the Cisco mesh.
Johnny
On 2021-11-18 01:16, Madeline Autumn-Rose wrote:
--
Madeline Autumn-Rose
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
Been awhile since I've posted anything, or
been connected but I'd like to
work on getting reconnected to HECnet.
I would still like to do Cisco connections - just need to pass that through
the firewall. Can a more-modern ISR running IOS-XE do DECnet? (specifically
a cisco 4321). Worst case I can just re-use the 2851, but that's got a lot
of telephony config on it so would like to separate out uses if possible.
(Also - you may have previously known me as Cory Smelosky - please update
contact details and whatnot)
I used to be area 9 - I will continue to use that area.
Thanks!
1:43 a.m.
On 11/17/21 7:38 PM, Madeline Autumn-Rose wrote:
--
On Thu, 18 Nov 2021, Johnny Billquist wrote:
Yes - others on the mesh, including Brian, may respond; I had sent you
the email below recently, feel free to reestablish your tunnel to
Area-31 and others. Are you still at 50.131.218.138?
Contact info updated, thanks.
Hi Cory,
I am not sure if Area-9 is reachable, but when you have a chance, can
you update your tunnel destination for Area-31 to 150.136.5.129 please?
I have moved
31.1023 to this IP (Oracle Cloud data center, Ashburn, Virginia).
Thanks.
Best regards,
Supratim
interface Tunnel9
?no ip address
?logging event subif-link-status
?decnet cost 9
?decnet routing-timer 20
?decnet router-priority 1
?tunnel source FastEthernet0/1
?tunnel destination 50.131.218.138
?tunnel path-mtu-discovery
Someone else will need to answer the question
about various Cisco
capabilities.
Can't even remember where you were hooked up to before, and we we
should resume that or find some other alternative.
I was previously part of the Cisco mesh. ?Johnny
On 2021-11-18 01:16, Madeline Autumn-Rose wrote:
Been awhile since I've posted anything, or
been connected but I'd
like to work on getting reconnected to HECnet.
I would still like to do Cisco connections - just need to pass that
through the firewall. Can a more-modern ISR running IOS-XE do
DECnet? (specifically a cisco 4321). Worst case I can just re-use
the 2851, but that's got a lot of telephony config on it so would
like to separate out uses if possible.
(Also - you may have previously known me as Cory Smelosky - please
update contact details and whatnot)
I used to be area 9 - I will continue to use that area.
Thanks!
1:50 a.m.
On Wed, 17 Nov 2021, Supratim Sanyal wrote:
On 11/17/21 7:38 PM, Madeline Autumn-Rose wrote:
73.223.113.75 now.
On Thu, 18 Nov 2021, Johnny Billquist wrote:
Yes - others on the mesh, including Brian, may respond; I had sent you the
email below recently, feel free to reestablish your tunnel to Area-31 and
others. Are you still at 50.131.218.138?
Someone else will need to answer the question
about various Cisco
capabilities.
Can't even remember where you were hooked up to before, and we we should
resume that or find some other alternative.
I was previously part of the Cisco mesh. Contact info updated, thanks.
Thanks.
Hi Cory,
I am not sure if Area-9 is reachable, but when you have a chance, can you
update your tunnel destination for Area-31 to 150.136.5.129 please? I have
moved
31.1023 to this IP (Oracle Cloud data center, Ashburn, Virginia).
Thanks.
Best regards,
Supratim
interface Tunnel9
?no ip address
?logging event subif-link-status
?decnet cost 9
?decnet routing-timer 20
?decnet router-priority 1
?tunnel source FastEthernet0/1
?tunnel destination 50.131.218.138
?tunnel path-mtu-discovery
--
Madeline Autumn-Rose
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
?Johnny
On 2021-11-18 01:16, Madeline Autumn-Rose wrote:
Been awhile since I've posted anything, or
been connected but I'd like to
work on getting reconnected to HECnet.
I would still like to do Cisco connections - just need to pass that
through the firewall. Can a more-modern ISR running IOS-XE do DECnet?
(specifically a cisco 4321). Worst case I can just re-use the 2851, but
that's got a lot of telephony config on it so would like to separate out
uses if possible.
(Also - you may have previously known me as Cory Smelosky - please update
contact details and whatnot)
I used to be area 9 - I will continue to use that area.
Thanks!
1:53 a.m.
On 11/17/21 7:50 PM, Madeline Autumn-Rose wrote:
--
On Wed, 17 Nov 2021, Supratim Sanyal wrote:
Updating and awaiting connection whenever you are ready. BTW,
DECnet/Python does GRE tunneling too.
Thanks.
On 11/17/21 7:38 PM, Madeline Autumn-Rose wrote:
73.223.113.75 now. On Thu, 18 Nov 2021, Johnny Billquist wrote:
Yes - others on the mesh, including Brian, may respond; I had sent
you the email below recently, feel free to reestablish your tunnel to
Area-31 and others. Are you still at 50.131.218.138?
Someone else will need to answer the question
about various Cisco
capabilities.
Can't even remember where you were hooked up to before, and we we
should resume that or find some other alternative.
I was previously part of the Cisco mesh. Contact info
updated, thanks.
Thanks.
Hi Cory,
I am not sure if Area-9 is reachable, but when you have a chance, can
you update your tunnel destination for Area-31 to 150.136.5.129
please? I have moved
31.1023 to this IP (Oracle Cloud data center, Ashburn, Virginia).
Thanks.
Best regards,
Supratim
interface Tunnel9
?no ip address
?logging event subif-link-status
?decnet cost 9
?decnet routing-timer 20
?decnet router-priority 1
?tunnel source FastEthernet0/1
?tunnel destination 50.131.218.138
?tunnel path-mtu-discovery
?Johnny
On 2021-11-18 01:16, Madeline Autumn-Rose wrote:
> Been awhile since I've posted anything, or been connected but I'd
> like to work on getting reconnected to HECnet.
>
> I would still like to do Cisco connections - just need to pass
> that through the firewall. Can a more-modern ISR running IOS-XE do
> DECnet? (specifically a cisco 4321). Worst case I can just re-use
> the 2851, but that's got a lot of telephony config on it so would
> like to separate out uses if possible.
>
> (Also - you may have previously known me as Cory Smelosky - please
> update contact details and whatnot)
>
> I used to be area 9 - I will continue to use that area.
>
> Thanks!
2 a.m.
On Wed, 17 Nov 2021, Supratim Sanyal wrote:
On 11/17/21 7:50 PM, Madeline Autumn-Rose wrote:
cisco-tandem#ping 31.1023
Type escape sequence to abort.
Sending 5, 100-byte DECnet echos to atg 0 area.node 31.1023, timeout is 5
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 72/80/88 ms
Looks like everything still works.
On Wed, 17 Nov 2021, Supratim Sanyal wrote:
Updating and awaiting connection whenever you are ready. BTW, DECnet/Python
does GRE tunneling too.
On 11/17/21 7:38 PM, Madeline Autumn-Rose wrote:
73.223.113.75 now. On Thu, 18 Nov 2021, Johnny Billquist wrote:
> Someone else will need to answer the question about various Cisco
> capabilities.
>
> Can't even remember where you were hooked up to before, and we we should
> resume that or find some other alternative.
>
I was previously part of the Cisco mesh.
Yes - others on the mesh, including Brian, may respond; I had sent you the
email below recently, feel free to reestablish your tunnel to Area-31 and
others. Are you still at 50.131.218.138?
Thanks.
--
Madeline Autumn-Rose
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
Contact
info updated, thanks.
Thanks.
Hi Cory,
I am not sure if Area-9 is reachable, but when you have a chance, can you
update your tunnel destination for Area-31 to 150.136.5.129 please? I have
moved
31.1023 to this IP (Oracle Cloud data center, Ashburn, Virginia).
Thanks.
Best regards,
Supratim
interface Tunnel9
?no ip address
?logging event subif-link-status
?decnet cost 9
?decnet routing-timer 20
?decnet router-priority 1
?tunnel source FastEthernet0/1
?tunnel destination 50.131.218.138
?tunnel path-mtu-discovery
> ?Johnny
>
> On 2021-11-18 01:16, Madeline Autumn-Rose wrote:
>> Been awhile since I've posted anything, or been connected but I'd like
>> to work on getting reconnected to HECnet.
>>
>> I would still like to do Cisco connections - just need to pass that
>> through the firewall. Can a more-modern ISR running IOS-XE do DECnet?
>> (specifically a cisco 4321). Worst case I can just re-use the 2851, but
>> that's got a lot of telephony config on it so would like to separate
>> out uses if possible.
>>
>> (Also - you may have previously known me as Cory Smelosky - please
>> update contact details and whatnot)
>>
>> I used to be area 9 - I will continue to use that area.
>>
>> Thanks!
>
>
1:59 a.m.
On 11/17/21 7:50 PM, Madeline Autumn-Rose wrote:
73.223.113.75 now.
Updated here.
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
I was previously part of the Cisco mesh.
Yes - others on the mesh, including Brian, may respond; I had sent you
the email below recently, feel free to reestablish your tunnel to
Area-31 and others. Are you still at 50.131.218.138?
2:02 a.m.
On Wed, 17 Nov 2021, Dave McGuire wrote:
On 11/17/21 7:50 PM, Madeline Autumn-Rose wrote:
73.223.113.75 now.
Updated here.
-Dave
cisco-tandem#ping 61.1023
Type escape sequence to abort.
Sending 5, 100-byte DECnet echos to atg 0 area.node 61.1023, timeout is 5
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 84/87/92 ms
Perfect. Just need to have Brian update the source interface for the
tunnels and enable SNMP and then I can auto-apply the configs.
--
Madeline Autumn-Rose
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
I was previously part of the Cisco mesh.
Yes - others on the mesh, including Brian, may respond; I had sent you the
email below recently, feel free to reestablish your tunnel to Area-31 and
others. Are you still at 50.131.218.138? 
9:43 a.m.
Give me the details and I'll update the DB.
Welcome back!
-brian
On 18/11/21 01:02, Madeline Autumn-Rose wrote:
On Wed, 17 Nov 2021, Dave McGuire wrote:
On 11/17/21 7:50 PM, Madeline Autumn-Rose wrote:
?Updated here.
?????? -Dave
cisco-tandem#ping 61.1023
Type escape sequence to abort.
Sending 5, 100-byte DECnet echos to atg 0 area.node 61.1023, timeout
is 5 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 84/87/92 ms
Perfect. Just need to have Brian update the source interface for the
tunnels and enable SNMP and then I can auto-apply the configs.
> I was
previously part of the Cisco mesh.
Yes - others on the mesh, including Brian, may respond; I had sent
you the email below recently, feel free to reestablish your tunnel
to Area-31 and others. Are you still at 50.131.218.138?
73.223.113.75 now.
6:06 p.m.
On Thu, 18 Nov 2021, Brian Hechinger wrote:
Give me the details and I'll update the DB.
Set the source interface to gi0/0, and update the IP to 73.223.113.75 -
I'll fix SNMP later today.
Welcome back!
Thanks!
-brian
On 18/11/21 01:02, Madeline Autumn-Rose wrote:
--
Madeline Autumn-Rose
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
On Wed, 17 Nov 2021, Dave McGuire wrote:
On 11/17/21 7:50 PM, Madeline Autumn-Rose wrote:
cisco-tandem#ping 61.1023
Type escape sequence to abort.
Sending 5, 100-byte DECnet echos to atg 0 area.node 61.1023, timeout is 5
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 84/87/92 ms
Perfect. Just need to have Brian update the source interface for the
tunnels and enable SNMP and then I can auto-apply the configs.
>> I was previously part of the Cisco mesh.
>
> Yes - others on the mesh, including Brian, may respond; I had sent you
> the email below recently, feel free to reestablish your tunnel to
> Area-31 and others. Are you still at 50.131.218.138?
73.223.113.75 now.
?Updated here.
?????? -Dave
6:22 p.m.
Let me know once you have. No point updating it in the DB until you do.
-brian
On 18/11/21 17:06, Madeline Autumn-Rose wrote:
On Thu, 18 Nov 2021, Brian Hechinger wrote:
Give me the details and I'll update the DB.
Set the source interface to gi0/0, and update the IP to 73.223.113.75
- I'll fix SNMP later today.
Welcome back!
Thanks!
-brian
On 18/11/21 01:02, Madeline Autumn-Rose wrote:
On Wed, 17 Nov 2021, Dave McGuire wrote:
On 11/17/21 7:50 PM, Madeline Autumn-Rose wrote:
>>> I was previously part of the Cisco mesh.
>>
>> Yes - others on the mesh, including Brian, may respond; I had
>> sent you the email below recently, feel free to reestablish your
>> tunnel to Area-31 and others. Are you still at 50.131.218.138?
>
> 73.223.113.75 now.
?Updated here.
?????? -Dave
cisco-tandem#ping 61.1023
Type escape sequence to abort.
Sending 5, 100-byte DECnet echos to atg 0 area.node 61.1023, timeout
is 5 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 84/87/92 ms
Perfect. Just need to have Brian update the source interface for the
tunnels and enable SNMP and then I can auto-apply the configs.
9:44 a.m.
On Thu, 18 Nov 2021 at 08:59, Dave McGuire <mcguire at neurotica.com> wrote:
On 11/17/21 7:50 PM, Madeline Autumn-Rose wrote:
73.223.113.75 now.
Updated here.
I have also updated my configuration. Glad to see you back!
Regards, Tim.
I was previously part of the Cisco mesh.
Yes - others on the mesh, including Brian, may respond; I had sent you
the email below recently, feel free to reestablish your tunnel to
Area-31 and others. Are you still at 50.131.218.138? 
2:04 a.m.
Do you have a list of nodes and names or are these already in Johnny's
data base?
On 11/17/21 7:16 PM, Madeline Autumn-Rose wrote:
Been awhile since I've posted anything, or been
connected but I'd like
to work on getting reconnected to HECnet.
I would still like to do Cisco connections - just need to pass that
through the firewall. Can a more-modern ISR running IOS-XE do DECnet?
(specifically a cisco 4321). Worst case I can just re-use the 2851,
but that's got a lot of telephony config on it so would like to
separate out uses if possible.
(Also - you may have previously known me as Cory Smelosky - please
update contact details and whatnot)
I used to be area 9 - I will continue to use that area.
Thanks!
2:04 a.m.
On Wed, 17 Nov 2021, Thomas DeBellis wrote:
Do you have a list of nodes and names or are these
already in Johnny's data
base?
Already in the database.
On 11/17/21 7:16 PM, Madeline Autumn-Rose wrote:
--
Madeline Autumn-Rose
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
Been awhile since I've posted anything, or
been connected but I'd like to
work on getting reconnected to HECnet.
I would still like to do Cisco connections - just need to pass that through
the firewall. Can a more-modern ISR running IOS-XE do DECnet? (specifically
a cisco 4321). Worst case I can just re-use the 2851, but that's got a lot
of telephony config on it so would like to separate out uses if possible.
(Also - you may have previously known me as Cory Smelosky - please update
contact details and whatnot)
I used to be area 9 - I will continue to use that area.
Thanks!
8:19 a.m.
Hello,
according to the cisco feature navigator ( https://cfnng.cisco.com/browse/routing/features
), DECnet IV is available only on ISR 4431 and ASR 1002-X (IOS-XE 17.5.1.a), DECnet V and
other few decnet features are available only on ASR 1002-X.
Ciao.
Fabio.
Il 18 Novembre 2021 01:16:53 CET, Madeline Autumn-Rose <b4 at gewt.net> ha scritto:
Been awhile since I've posted anything, or been
connected but I'd like to
work on getting reconnected to HECnet.
I would still like to do Cisco connections - just need to pass that
through the firewall. Can a more-modern ISR running IOS-XE do DECnet?
(specifically a cisco 4321). Worst case I can just re-use the 2851, but
that's got a lot of telephony config on it so would like to separate out
uses if possible.
(Also - you may have previously known me as Cory Smelosky - please update
contact details and whatnot)
I used to be area 9 - I will continue to use that area.
Thanks!
--
Madeline Autumn-Rose
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
--
Inviato dal mio dispositivo Android con K-9 Mail. Perdonate la brevit?.
4:27 p.m.
The 4331 does not support DECnet. It has not been removed from the code but, if you try
to run it, the router will crash.
On Nov 18, 2021, at 12:19 AM, Fabio Bizzi
<fabioforum at bizzi.org> wrote:
Hello,
according to the cisco feature navigator (
https://cfnng.cisco.com/browse/routing/features
<https://cfnng.cisco.com/browse/routing/features> ), DECnet IV is available only on
ISR 4431 and ASR 1002-X (IOS-XE 17.5.1.a), DECnet V and other few decnet features are
available only on ASR 1002-X.
Ciao.
Fabio.
Il 18 Novembre 2021 01:16:53 CET, Madeline Autumn-Rose <b4 at gewt.net> ha
scritto:
Been awhile since I've posted anything, or been connected but I'd like to
work on getting reconnected to HECnet.
I would still like to do Cisco connections - just need to pass that
through the firewall. Can a more-modern ISR running IOS-XE do DECnet?
(specifically a cisco 4321). Worst case I can just re-use the 2851, but
that's got a lot of telephony config on it so would like to separate out
uses if possible.
(Also - you may have previously known me as Cory Smelosky - please update
contact details and whatnot)
I used to be area 9 - I will continue to use that area.
Thanks!
--
Madeline Autumn-Rose
http://gewt.net <http://gewt.net/> Personal stuff
http://gimme-sympathy.org <http://gimme-sympathy.org/> Projects
--
Inviato dal mio dispositivo Android con K-9 Mail. Perdonate la brevit?.
6:06 p.m.
On Thu, 18 Nov 2021, Mark Berryman wrote:
--
Madeline Autumn-Rose
http://gewt.net Personal stuff
http://gimme-sympathy.org Projects
The 4331 does not support DECnet. It has not been
removed from the code but, if you try to run it, the router will crash.
Well that's unfortunate. Multipurposing the 2851 it is!
On Nov 18,
2021, at 12:19 AM, Fabio Bizzi <fabioforum at bizzi.org> wrote:
Hello,
according to the cisco feature navigator (
https://cfnng.cisco.com/browse/routing/features
<https://cfnng.cisco.com/browse/routing/features> ), DECnet IV is available only on
ISR 4431 and ASR 1002-X (IOS-XE 17.5.1.a), DECnet V and other few decnet features are
available only on ASR 1002-X.
Ciao.
Fabio.
Il 18 Novembre 2021 01:16:53 CET, Madeline Autumn-Rose <b4 at gewt.net> ha
scritto:
Been awhile since I've posted anything, or been connected but I'd like to
work on getting reconnected to HECnet.
I would still like to do Cisco connections - just need to pass that
through the firewall. Can a more-modern ISR running IOS-XE do DECnet?
(specifically a cisco 4321). Worst case I can just re-use the 2851, but
that's got a lot of telephony config on it so would like to separate out
uses if possible.
(Also - you may have previously known me as Cory Smelosky - please update
contact details and whatnot)
I used to be area 9 - I will continue to use that area.
Thanks!
--
Madeline Autumn-Rose
http://gewt.net <http://gewt.net/> Personal stuff
http://gimme-sympathy.org <http://gimme-sympathy.org/> Projects
--
Inviato dal mio dispositivo Android con K-9 Mail. Perdonate la brevit?.
904
days inactive
904
days old
17 comments
9 participants
participants (9)
-
b4＠gewt.net -
bqt＠softjar.se -
fabioforum＠bizzi.org -
mark＠theberrymans.com -
mcguire＠neurotica.com -
supratim＠riseup.net -
tim＠sneddon.id.au -
tommytimesharing＠gmail.com -
wonko＠4amlunch.net