5 Sep
2025
5 Sep
'25
7:46 p.m.
These are all simulated machines running on raspberry pi's. I run 4 instances
(machines) on each pi. All pi's connect into a simple TPlink 8 port switch. Nothing is
on wifi.
On Friday, September 5, 2025 at 01:41:53 PM EDT, Brian Roth
<abacos_98(a)yahoo.com> wrote:
I'm confused? Geezer is 31.279 not 278. 278 is HOWARD and it is a router on the
network. It can communicate with all other nodes and I just did a set host with IMPVAX
31.1.I shutdown Howard (278) and now the microvax (SCOOBY) shows my Pydecnet router 31.279
(geezer) as its designated router after a SHOW Circuit but still a no go.
On Friday, September 5, 2025 at 01:15:07 PM EDT, Johnny Billquist
<bqt(a)softjar.se> wrote:
Well, GEEZER (31.278) is not seeing 31.282 as up. So that's why you have
a problem. This usually means that packets are working in one direction,
but not the other.
Was this a real machine? How have you connected it to the rest of the
network?
Johnny
On 2025-09-05 18:45, Brian Roth wrote:
The address is 31.282. No File access, Phone or NCP
Tell to other nodes
but it is still able to go out and find a router. It (31.282) can phone
itself and set host but other nodes it just hangs. If I phone another
node it will just sit at "Establishing Decnet Link and then error to
"Node is not reachable.
Brian.
On Friday, September 5, 2025 at 12:38:11 PM EDT, Johnny Billquist
<bqt(a)softjar.se> wrote:
No. Qbus ethernet or Unibus ethernet makes no difference here.
Does anything else work? NCP to other nodes? Phone? File access?
What's the address of that microvax?
Johnny
On 2025-09-05 17:59, Brian Roth wrote:
--
Johnny Billquist || "I'm on a bus
|| on a psychedelic trip
email: bqt(a)softjar.se || Reading murder books
pdp is alive! || tryin' to stay hip" - B. Idol
_______________________________________________
HECnet mailing list -- hecnet(a)lists.dfupdate.se
To unsubscribe send an email to hecnet-leave(a)lists.dfupdate.se
Hello, I currently have 8 simh vax machines on
Hecnet all working fine.
Its a mix of machines running VMS 3.5 to 7.3 and while some were a bit
of a challenge they all talk. I recently configured a Microvax II with
MicroVMS 4.6 as well as Decnet 4.6 and assigned it to my area 31. The
network loads without errors and I am able to SET HOST to itself butto
no other nodes in my area or vice versa. SHOW KNOWN CIRCUITS shows the
hosts I manually defined. SHOW KNOWN CIRCUITS CHARACTERISTICS shows a
designated router in my area so its finding that. If I bring a router
node down it successfully finds another in the area.
The microvax node:
Known Circuit Volatile Characteristics as of 5-SEP-1987 11:37:16
Circuit = QNA-0
State = on
Service = disabled
Designated router = 31.278
Cost =4
Router priority =64
Hello timer = 15
Type = Ethernet
Adjacent node =31.278
Listen timer = 45
The working nodes match with the exception of the circuit. All the other
machines are UNA-0 (UNIBUS) and this one is of course QNA-0 Couldthis
be the problem?
Brian.
_______________________________________________
HECnet mailing list -- hecnet(a)lists.dfupdate.se
<mailto:hecnet@lists.dfupdate.se>
To unsubscribe send an email to
hecnet-leave(a)lists.dfupdate.se
<mailto:hecnet-leave@lists.dfupdate.se>
--
Johnny Billquist || "I'm on a bus
|| on a psychedelic trip
email: bqt(a)softjar.se <mailto:bqt@softjar.se> || Reading
murder books
pdp is alive! || tryin' to stay hip" - B. Idol
_______________________________________________
HECnet mailing list -- hecnet(a)lists.dfupdate.se
<mailto:hecnet@lists.dfupdate.se>
To unsubscribe send an email to hecnet-leave(a)lists.dfupdate.se
<mailto:hecnet-leave@lists.dfupdate.se>
_______________________________________________
HECnet mailing list -- hecnet(a)lists.dfupdate.se
To unsubscribe send an email to hecnet-leave(a)lists.dfupdate.se