16 Jul
2019
16 Jul
'19
8:04 p.m.
On Jul 16, 2019, at 1:08 PM, Johnny Billquist <bqt
at softjar.se> wrote:
On 2019-07-16 17:50, John Forecast wrote:
Ah, yes, I tend to skim over the mP changes, but you are right. DECnet is one of those
things that got hit because of that, as well as some kernel parts. It's still fairly
contained. It's just that CEX knows a little too much to not get affected. Most device
drivers are totally unaware of mP aspects.
It?s right on the hairy edge since it does its own driver loading and interrupt
handling. We first got DECnet-11M+ running on a standard 11/70 configuration and then I
managed to get time on the RSX-11M+ development quad processor (CASTOR::/POLLUX::) which
had its own machine room within the larger lab space - pretty much every known Unibus
device was attached to that machine. Booted my image and started DECnet running (this was
Phase III so probably DMC/DMR connectivity) and everything went silent followed by each
console typing an XDT> prompt in sequence - my total test run had probably lasted 5
minutes. Somewhere in the interrupt logic I had missed a cache bypass or cache flush and
all 4 processors had the same memory location in their caches and were quite happily using
it to modify memory.
On Jul
15, 2019, at 7:48 PM, Johnny Billquist <bqt at softjar.se> wrote:
On 2019-07-15 17:36, John Forecast wrote:
There were a lot of small changes throughout the networking code to get it
running on our dual-processor. We eventually shipped with the kernel networking code
running with cache bypass enabled and the intention of revisiting it in a later release.
One the 11/74 was cancelled, we were never given the opportunity? > On Jul 14, 2019, at 11:55 PM, Thomas DeBellis
<tommytimesharing at gmail.com <mailto:tommytimesharing at gmail.com>> wrote:
>
2. RSX-11M/11S - any PDP-11 system with sufficient memory + devices
Device drivers ran as part of the ?kernel? serialized by the fork block mechanism
Right. And I/O completion is normally handled by a couple of routines in the kernel, so
the driver itself can be pretty minimal.
I guess RSX-11M+ could be consider a separate
class adding I/D space, supervisor mode and multi-processor support.
Nah. 11M+ is really very similar to 11M. They pretty much share the same codebase, but M+
extends some data structures with a bit more information, and also adds a couple of more
structures to make the system more flexible.
The splitting of I/D space, as well as supervisor mode actually have very little impact
on the kernel. There is obviously a bit more work at a context switch, and there are a
couple of details around ASTs, which can switch between user and supervisor, but much of
the rest don't know or care. And drivers can pretty much be moved straight over,
although you normally would want to modify them to take advantage of some nifty additional
capabilities provided by M+.
Interesting that you think you might have improved
DECnet with a bit more work. As it stands, it works fine today. But I haven't looked
into how much might be running without cache enabled. But I am running a simulated 11/74.
That is Mim.Update.UU.SE. You can both browse to it, and telnet to it. Usually I only have
two CPUs online, since there are still some issues with the emulation. But otherwise it
works fine.
Does the simulator actually simulate the caches or just the control registers like
SIMH?
I also had to figure out some issues with TCP/IP and
multiprocessor support. That was interesting. :-)
That must be a Mentec release? I was long gone from DEC at that point in time.
Yes. Mentec released both 4.5 and 4.6 of M+. The last DEC release was V4.4, in 1993 or
1994. Right before it was sold off to Mentec.
(Corresponding 11M was 4.7 and 4.8, with the last DEC release being 4.6.)
The M+ 4.6 disk image at trailing-edge actually contains the DECnet code as well. And
yes, DECnet-11M-PLUS V4.5 and V4.6 was released in parallel with RSX-11M-PLUS V4.5 and
V4.6.
Yes, I saw that one. I?m still looking for a router implementation - the latest
I?ve seen is for 11M+ V4.2
John.
> 1. What is the latest Phase DECnet that 11M will
run? I guess the
> last release was 93?
Phase IV. The last release I see on bitsavers.org <http://bitsaver.org> was 4.5 in
Oct 1989
No. Last/latest release was in 1998/1999 (depends on whether you look at 11M or 11M+).
But it was still all just phase IV.
Latest
11M is V4.8, and latest 11M+ is V4.6.
I think they are even available to trailing-edge?
That?s the base 11M/11M+ distribution? Do you know if there was a corresponding
DECnet release? Johnny
--
Johnny Billquist || "I'm on a bus
|| on a psychedelic trip
email: bqt at softjar.se || Reading murder books
pdp is alive! || tryin' to stay hip" - B. Idol