[HECnet] Decnet on RSX-11

On Jun 8, 2019, at 9:32 AM, Supratim Sanyal <supratim at riseup.net> wrote: Mark, 1) How does one get a copy of the ?FRODO distribution?? 2) if possible, I would like a redundant MULTINET TCP connection to your area from IMPVAX which can be a server or a client. Best, Supratim --- Supratim Sanyal, W1XMT 39.19151 N, 77.23432 W QCOCAL::SANYAL via HECnet > On Jun 8, 2019, at 9:11 AM, Kurt Hamm <kurt at hamm.me> wrote: > > He has definitely said that more than once. I just wasn't getting it. > > Sorry about that Johnny. > > Kurt > > On Sat, Jun 8, 2019, 8:14 AM Mark Matlock <mark at matlockfamily.com> wrote: > Kurt, > As Johnny says you should read chapter 10 of [IP]README.DOC and run a NETGEN to add the IP HECnet device. I?ve attached a walk-through of a NETGEN that can help guide you but you should understand the information in chapter 10. > > You should have a unique DECnet node address for your system (from Johnny) to use instead of the one I supplied in the walk-through. > > Later when bringing up IP-0-0 in the [IPNET]INS.CMD I think you need a port # for attachment to MIM if that is where you are connecting to? > > Best, > Mark > > > > > >> On Jun 8, 2019, at 6:36 AM, Kurt Hamm <kurt at hamm.me> wrote: >> >> Thanks Johnny and thanks Mark. For some reason I thought that this was already done since IP was working. >> >> This is just what I needed to know to finish this thing off. I really appreciate the assistance. >> >> Kurt >> >> On Sat, Jun 8, 2019, 5:32 AM Johnny Billquist <bqt at softjar.se> wrote: >> Kurt, Mark is absolutely right. >> >> You do not have the IP line driver generated into DECnet. >> >> This is what I suspect quite a few mails back between us, and tried to >> point out. >> >> And do not try to just edit CEMAC.MAC to add those lines Mark mention. >> That will not work. You need to run through the DECnet generation >> process, and then the IPNET postprocessing step. It's all in the TCP/IP >> manual, if you read it. >> >> Johnny >> >>> On 2019-06-08 05:58, Mark Matlock wrote: >>> Kurt, >>> I think you need to have the ?IP" network device NETGENed into DECnet. >>> >>> The fact that you first error occurs at the NCP SET PROC IP TOP makes me think that DECnet does not have a driver for the IP device loaded. When I made the ?Frodo? distribution available, I did a new SYSGEN for an 11/70 and also a NETGEN. In the NETGEN for the Unibus system a ?UNA? was the ethernet device and on a Qbus system (the actual Frodo 30.1) a QNA device is used. >>> >>> It would be helpful if you typed out LB:[5,54]CETAB.MAC as it could confirm if the IP device has been NETGENed in or not. In CETAB.MAC the 3rd actual line of code should look like: >>> >>> PDV$DF <AUX,EVL,ECL,XPT,NCT,RTH,LAT,DLX>,<EPM>,<UNA,IP> >>> >>> Three lines below that should be: >>> >>> SLT$DF IP,IP,XPT,LF.TIM,0,0,,0.,0.,15. >>> >>> It?s been a while since I added the IP-0-0 LIN and Circuits to my system, but I try to do that to one of my PiDP-11s and post the walk through for it. >>> >>> Below I?ve put some information of the sequence of startup command files that may help you understand the files involved. >>> >>> In the LB:[1,2]STARTUP.CMD of the Frodo distribution RSX and DECnet are started as is normal for any RSX. It then chains to LB:[1,2]INSPROG.CMD which brings up the DU1: disk that you either download from RSX11M.COM or the Simh boot.ini will make a blank one. >>> >>> At the end of the INSPROG.CMD two questions are asked with timeouts. The first will load LAT and the second loads Johnny?s TCP/IP. It loads the TCP/IP by chaining to LB:[IP]IPINS.CMD which will load TCP/IP and either DHCP an IP address or set a static IP address. At the end of that file then LB:[IP]IPAPPL.CMD is executed which sets up FTP, TELNET, NTP and other applications. >>> >>> Now, in the Frodo distribution IPAPPL.CMD, there is a line that was either commented or deleted that chains to LB:[IPNET]INSHECNET.CMD which is used to link the actual node Frodo (HECnet 30.1) to MIM >>> >>> Your [IPNET]INS.CMD looks identical to the INSHECNET.CMD on Frodo including the host port # which may be something we need to change? >>> >>> Do you have a HECnet address from Johnny? Also, where are you planning to connect to HECnet? >>> >>> There is a [IPNET]INS.NEW which is the template that Johnny provides and it does not have a port specified on MIM. I don?t remember the exact mechanics on MIM That accepts connections but that may be a function of that port # Frodo connects to MIM on IP-0-10 but that is not specified on Frodo but on MIM. >>> >>> Best, >>> Mark >>> >>> >>> >>> >>> >>>> On Jun 7, 2019, at 9:35 PM, Kurt Hamm <kurt at hamm.me> wrote: >>>> >>>> So, I added this command to the startup.cmd: @LB:[IPNET]INS.CMD. >>>> >>>> I didn't modify the file yet. I wanted to see what it would do >>>> >>>> The result after rebooting was this: >>>>> INS LB:[IPNET]MLTCOM/UIC=[1,54]/PRO=[RW,RW,,] >>>>> INS LB:[IPNET]MLTNET >>>>> INS LB:[IPNET]MLTCFG >>>>> NCP SET PROC IP TOP >>>> NCP -- Set failed, unrecognized component, Process >>>>> NCP SET LIN IP-0-* ALL >>>> NCP -- Set failed, invalid identification format, Line >>>>> MNC SHO VER >>>> Initialize common >>>> NT.IP not found. Exiting... >>>>> MNC SET CIR IP-0-0 TCA HOST MIM.UPDATE.UU.SE:7705 PORT 0 >>>> Initialize common >>>> NT.IP not found. Exiting... >>>>> NCP SET CIR IP-0-0 STA ON >>>> NCP -- Set failed, invalid identification format, Circuit >>>> >>>> There are lots of errors, so I am not sure where to start. >>>> >>>> Any advice would be appreciated. >>>> >>>> Kurt >>> >> >> >> -- >> Johnny Billquist || "I'm on a bus >> || on a psychedelic trip >> email: bqt at softjar.se || Reading murder books >> pdp is alive! || tryin' to stay hip" - B. Idol >