[HECnet] Emulated XQ polling timer setting and data overrun

On 2014-06-06 01:16, Mark Pizzolato - Info Comm wrote: On Thursday, June 05, 2014 at 12:04 PM, Johnny Billquist wrote: On 2014-06-05 20:46, Mark Pizzolato - Info Comm wrote: On Thursday, June 05, 2014 at 10:53 AM, Johnny Billquist wrote: On 2014-06-05 19:23, Paul_Koning at Dell.com wrote: On Jun 5, 2014, at 12:47 PM, Johnny Billquist <bqt at softjar.se> wrote: Interesting. I still have real network issues with the latest simh talking to a real PDP-11 sitting on the same physical network. So you seem to have hit sime other kind of limitation or something... I wouldn't think that traffic between PDP11 systems would put so much data in flight that all of the above issues would come into play. Hmmm...Grind...Grind... I do seem have some vague recollection of an issue with some DEQNA devices not being able to handle back-to-back packets coming in from the wire. This issue might have been behind DEC's wholesale replacement/upgrading of every DEQNA in the field, and it also may have had something to do with the DEQNA not being officially supported as a cluster device... Hey, just do: sim> SET XQ TYPE=DELQA-T and your all good. :-) Too bad you can't just upgrade real hardware like that. Uh... It's the PDP-11 that have problems receiving packets, not simh. I knew that. It was a joke. Notice ":-)".... Well, it was ambiguous. :-) Also, my PDP-11 already have a DELQA-T. :-) Finally, of course a simulated PDP-11 running on a fast machine will be able to output data at a high rate. Why would it not? It would. I never argued that it wouldn't. I read it as you was thinking that it would not. Maybe I'm being too literal tonight. Two real PDP-11 systems do not get any problems. Sending data from a real PDP-11 to the one in simh (or whatever) does not have any problems either. It is only when you send lots of data from a simulated machine (be that a PDP-11 or a VAX) to a real PDP-11 that you get these issues. I would suspect you should be able to see similar issues if the receiving end was physical VAX as well. I just tried to fire up the old VAX Station 4000 I've got on the shelf. This system hasn't been booted in more than 5 years (maybe 10). When it last booted, it didn't have any working disks, so I was planning to boot it into a cluster from my simh host. Without a disk, I'll have to create a RAM disk to test file copies from simh side to real side... I haven't had a monitor for the system for at about 15 years, but the last booting activities worked fine with a cable to one of the serial ports. But today it doesn't work. :-( You would have to boot VMS, since you don't have DECnet under much else. (I know you could have Ultrix with DECnet, but I somehow don't think that's the right way... :-) ) The problem is also partly DECnet. DECnet do not seem to keep packets that arrive out of order. So if a packet in a sequence is lost, DECnet is going to retransmit all packets from that point forward. Meaning that when the session timer times out, the retransmission happens, and then you will yet again drop a packet in the whole sequence of packets that are sent. Each time the session timer times out, DECnet also do a backoff on the timeout time of that timer, until the session timer is about 2 minutes. So after a while you end up with DECnet sending a burst of packets, some of which are lost. It then takes about 2 minutes before a retransmission happens, at which point you get another 2 minute timeout. Thus, performance sucks. TCP/IP is better (well, my TCP/IP anyway), in that when I loose a packet, I still keep whatever later packets I get, so after a while I get to a stable mode where TCP only sends one packet at a time, since the window is full. Only actually lost packets needs to be retransmitted, so I actually do get to this stable point. OK. So you sound like you really need a throttling option for the LAN devices. I'll look over the throttling logic in the bridge and fold in something similar. Well, I'm not so sure that code should be a model to pattern anything after. Everything about my bridge is just a hack. Done just to fix an immediate problem without any proper design at any corner. :-) Johnny -- Johnny Billquist || "I'm on a bus || on a psychedelic trip email: bqt at softjar.se || Reading murder books pdp is alive! || tryin' to stay hip" - B. Idol