[HECnet] Cisco tunnels: update my IP

I need to keep the router and switch maintained so I don't get calls at 4am because my dad needs to check sports scores. ;) ----- Original Message ----- > "Downloading the entire Internet"...I love it. :) > > I didn't know you were still running hardware at your old place in Ohio..? > > -Dave > > On 06/23/2016 12:09 PM, Cory Smelosky wrote: >> With ZFS replication across work/home and home/old Ohio stuff, downloading the >> entire internet, and being impatient...I do quite regularly max it out. ;) >> >> ----- Original Message ----- >>> From: "Dave McGuire" <mcguire at neurotica.com> >>> To: hecnet at Update.UU.SE >>> Sent: Thursday, June 23, 2016 8:14:53 AM >>> Subject: Re: [HECnet] Cisco tunnels: update my IP >> >>> Nice and all...but how much are you actually *using*? ;) >>> >>> -Dave >>> >>> -- >>> Dave McGuire, AK4HZ >>> New Kensington, PA >>> >>> >>> >>> On June 23, 2016 11:13:04 AM Cory Smelosky <b4 at gewt.net> wrote: >>> >>>> 175/10 cable with a constant ache to upgrade to gigabit from one of the >>>> providers. ;) >>>> >>>> ----- Original Message ----- >>>>> From: "Brian Hechinger" <wonko at 4amlunch.net> >>>>> To: hecnet at Update.UU.SE >>>>> Sent: Thursday, June 23, 2016 8:09:24 AM >>>>> Subject: Re: [HECnet] Cisco tunnels: update my IP >>>> >>>>> What sort of connection do you have? >>>>> >>>>> -brian >>>>> >>>>>> On Jun 23, 2016, at 10:55, Cory Smelosky <b4 at gewt.net> wrote: >>>>>> >>>>>> ...it also exceeds the capabilities of a 2851. >>>>>> >>>>>> Sent from my iPhone >>>>>> >>>>>>> On Jun 23, 2016, at 07:26, Cory Smelosky <b4 at gewt.net> wrote: >>>>>>> >>>>>>> My connection exceeds the capabilities of the 2620 or I would. >>>>>>> >>>>>>> Sent from my iPhone >>>>>>> >>>>>>>> On Jun 23, 2016, at 05:30, Peter Lothberg <roll at Stupi.SE> wrote: >>>>>>>> >>>>>>>> >>>>>>>> Why don't you put your 2600 as your boarder-gw? >>>>>>>> >>>>>>>> interface Tunnel1 >>>>>>>> ip address 192.108.195.70 255.255.255.252 >>>>>>>> ip router isis >>>>>>>> ipv6 address 2001:440:1880:ABCD::2/64 >>>>>>>> ipv6 enable >>>>>>>> ipv6 mtu 1420 >>>>>>>> ipv6 router isis >>>>>>>> decnet cost 1 >>>>>>>> isis metric 2 >>>>>>>> tunnel source ATM0/1/0.1 >>>>>>>> tunnel destination 192.36.147.120 >>>>>>>> ! >>>>>>>> interface ATM0/1/0 >>>>>>>> mtu 4470 >>>>>>>> no ip address >>>>>>>> ip virtual-reassembly in max-fragments 64 max-reassemblies 512 >>>>>>>> load-interval 30 >>>>>>>> atm restart timer 90 >>>>>>>> no atm ilmi-keepalive >>>>>>>> dsl enable-training-log delay 0 >>>>>>>> dsl power-cutback 6 >>>>>>>> dsl noise-margin -2 >>>>>>>> dsl gain-setting rx-offset 3 >>>>>>>> dsl bitswap both >>>>>>>> ! >>>>>>>> interface ATM0/1/0.1 point-to-point >>>>>>>> mtu 4470 >>>>>>>> ip dhcp client broadcast-flag set >>>>>>>> ip address dhcp >>>>>>>> ip nat outside >>>>>>>> ip virtual-reassembly in >>>>>>>> atm route-bridged ip >>>>>>>> pvc 0/35 >>>>>>>> protocol bridge >>>>>>>> encapsulation aal5snap >>>>>>>> >>>>>>>> -P >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>>>> On 23/06/2016 1:47 PM, Cory Smelosky wrote: >>>>>>>>>> Found the actual problem! >>>>>>>>>> >>>>>>>>>> IPSec VTI VPNs means I can't do source-based NAT/firewall rules to redirect GRE >>>>>>>>>> from the DECnet tunnel IPs to a separate box as is currently configured. >>>>>>>>>> >>>>>>>>> >>>>>>>>> So, does this mean that you're still off the air? >>>>>>>>> >>>>>>>>> Regards, Tim. >>>>>>>>> >>>>>>>>> >>>>>>>> >>>>>>>> ` > > -- > Dave McGuire, AK4HZ > New Kensington, PA