28 Jul
2019
28 Jul
'19
6 p.m.
I should correct myself. The exact formula for how the listen timer is
set, based on the remote hello timer, is a bit more complex. I remember
that I saw it described somewhere, but cannot remember the details right
now.
So my "two times hello plus some jiffy" is rather incorrect in fact. It
turns out to that for some values in the end, but it varies because of
other parameters as well.
But the basic principle is correct. The listen timer is based on the
hello timer, and is used to determine if a circuit is down. And the
hello timer is the interval at which hello packets are sent on the circuit.
And changing the hello timer causes less traffic, and longer time before
a circuit down is detected (unless some other mechanism allows detection
of a circuit down earlier).
Johnny
On 2019-07-28 17:52, Johnny Billquist wrote:
The hello timer is essentially how long between the
node sends out the
hello messages on a circuit. This in turn, is used to detect when a
circuit goes down.
The listen timer is on a per node basis for adjacent nodes, and is set
to two times the hello time, plus a few seconds. So the detection of a
circuit going down is when the listen time expires.
You cannot directly set the listen timer, but you can choose your own
hello timers, and having a longer time means the other end will take
longer before it detects a circuit going down.
All that said, I usually have long times, since I do not feel really
quick detection of a circuit down is that important, but I don't mind
reducing the traffic a load a little.
Other than that, everyone should feel free to make whatever choice they
feel most appropriate for their expectations.
? Johnny
On 2019-07-28 16:41, Mark Matlock wrote:
--
Johnny Billquist || "I'm on a bus
|| on a psychedelic trip
email: bqt at softjar.se || Reading murder books
pdp is alive! || tryin' to stay hip" - B. Idol
Johnny,
??? I have one question I?ve been meaning to ask about hello timers
and listen timers. The default seems to to be 15 seconds hello and 40
seconds listen. But on MIM I have seen some other combinations like
Hello 300 secs but the Listen varies from 608 to the default 40 (at
least on IP-0-10)
All the values seem to work ok, but on my 30.1 node which is a real
PDP-11, I?d like to use something closer to 300 and 600+ to reduce
load and unneeded up and down messages due to my flakey ISP?s internet.
What are your thoughts on this topic?
Thanks!
Mark
On Jul 28, 2019, at 8:31 AM, Johnny Billquist
<bqt at softjar.se> wrote:
People, I have written a page about DECnet costs and HECnet costs,
which I would recommend that anyone interested read through. It
contains a bit of elaboration on how DECnet does routing, and gives
some suggestions on how costs could be set on HECnet to make it
perform better.
I have noticed over the years that sometimes we do get really silly
routing decisions just because of how people set, or do not set
costs. The page I've written is by no means perfect, nor are the
suggestions in there. But feel free to come with feedback, or ignore
it. But I am going to try and use this myself more properly from now
on, and that means that if others don't, you probably are going to
get more traffic through your nodes. Traffic that probably do not
make sense that it passes through you, but I just feel that I prefer
to try and make it work right from my point of view, and then just at
least tell people how I worked my numbers out. If someone have a
different idea, I'm open to changing my settings, but I will not try
and do optimizations to achieve:
a) Same paths for packets in both directions - DECnet explicitly does
not do this.
b) Specifically penalize one type of interface because of any
subjective preference about that type of interface in general.
Oh - and the link to my writeup: http://mim.update.uu.se/costs.htm
? Johnny
--
Johnny Billquist????????????????? || "I'm on a bus
????????????????????????????????? ||? on a psychedelic trip
email: bqt at softjar.se???????????? ||? Reading murder books
pdp is alive!???????????????????? ||? tryin' to stay hip" - B. Idol