[Simh] [HECnet] TOPS-20 V4.1 DECnet

Actually the situation is somewhat more complex but is difficult to see exactly as the OPR on the Pdp10 7.02 does not function, so NCP cannot be used to define nodes and give status. The phase-III thinks the following: [DECnet network: local node SWBW08, 2 reachable nodes] Name Number Line Cost Hops L.Links Delay SWBW08 (58) local 0 0 (44) DMR-1-0 1023 31 The Tops20 4.1 thinks: Local DECNET node: SWBX05 Accessible DECNET nodes are: SWBX04 SWBX05 and: Status as of 3-May-2014 02:07:01 Line ID State Adjacent Node KDP_0_0 On SWBX04 KDP_0_1 On Function completed successfully Node 44 is the Swbx04 with is connected to the phase III So the phase-III thinks the Tops20 node is up, however the Tops20 node thinks otherwise. So somewhat more is functioning than directly meets the eye! Regards, Reindert -----Original Message----- From: simh-bounces at trailing-edge.com [mailto:simh-bounces at trailing-edge.com] On Behalf Of Cory Smelosky Sent: Saturday, May 03, 2014 00:52 Cc: simh at trailing-edge.com Subject: Re: [Simh] [HECnet] TOPS-20 V4.1 DECnet On Sat, 3 May 2014, Johnny Billquist wrote: Hi. On 2014-05-02 20:02, simh at swabhawat.com wrote: Hi guys, Well, if it truly is Phase II, then yeah, I would not expect it to work. But I was pretty sure it was Phase III, in which case it should work. There's a tape listed as Phase III...is it not Phase III?! Further there is no difference between the functioning of a Rsts-E 10.1 and a Rsx11MP46 Pdp11 with respect to Dup/Dmc/Ethernet if Rsts-E will support the Dup/Dmc lines and will route as it is primarily an Ethernet system. Well, therein lies the problem. RSTS/E simply did not support a bunch of thing that RSX did support. But yes, assuming the OS support a device, it should work equally well under RSTS/E and RSX. Huh. To make these things work the following has to be done: 1. Upgrade Tops20-4.1 Decnet to real phase-III, it then will link to a Pdp10 Tops10 7.02 based phase-III router. 2. Repair/upgrade the Tops10 7.02 router code so that it will talk to a phase-IV node. What is wrong with the Tops-10 DECnet phase III code if it don't interoperate with a phase IV node? Both things will require Tops monitor programming; the Tops10 7.02 case will probably be the most simple of the two. On the physical plane nothing is wrong as the packets do flow; only the DDCMP communication process will not startup; it hangs around in the startup phase. That's sad. But DDCMP should not be too hard to get working. And RSX support DDCMP both on synchronous and asynchronous serial lines. And both using devices that implement DDCMP, and software implemented DDCMP. Johnny Best regards Reindert -----Original Message----- From: simh-bounces at trailing-edge.com [mailto:simh-bounces at trailing-edge.com] On Behalf Of Cory Smelosky Sent: Friday, May 02, 2014 19:31 To: hecnet at Update.UU.SE Cc: simh at trailing-edge.com Subject: Re: [Simh] [HECnet] TOPS-20 V4.1 DECnet On Fri, 2 May 2014, Paul_Koning at Dell.com wrote: On May 2, 2014, at 12:59 PM, Mark Pizzolato - Info Comm <Mark at infocomm.com> wrote: On Friday, May 02, 2014 at 7:36 AM, Paul Koning wrote: ...If you want a RSTS system to connect to your Phase III machine, you'll want to use a DMC (or DMR/DMP/DMV, they are all roughly interchangeable). In a sufficiently recent SIMH, the DMC emulation speaks real DDCMP so it should talk with a software DDCMP implementation, such as one that uses a DUP. The DUP has only been tested talking to the KDP and DMC/DMR on RSX. If someone wants to try on RSTS I'd like to know if any issues are found. I'll see what I can do. Since a DMC/DMR does DDCMP itself, it shouldn't matter what OS is talking to it; if you get success with DECnet/RSX, I would expect it to work with DECnet/E as well. Or, since it doesn't know sync from async, it will probably talk to a software DDCMP implementation that uses a terminal interface. I believe that it should also talk to an OS based DDCMP implementation which uses Async ports. If someone is willing to test this, I'll work on any kinks which may be found which might inhibit this. I'm trying to make some progress on that (using RSTS V10.1). Let me know. I'm interested in using RSTS/E to link TOPS-20/KS. paul -- Cory Smelosky http://gewt.net Personal stuff http://gimme-sympathy.org Projects _______________________________________________ Simh mailing list Simh at trailing-edge.com http://mailman.trailing-edge.com/mailman/listinfo/simh -- Cory Smelosky http://gewt.net Personal stuff http://gimme-sympathy.org Projects _______________________________________________ Simh mailing list Simh at trailing-edge.com http://mailman.trailing-edge.com/mailman/listinfo/simh _______________________________________________ Simh mailing list Simh at trailing-edge.com http://mailman.trailing-edge.com/mailman/listinfo/simh