HECnet

hecnet@lists.dfupdate.se

15586 discussions

by gregg.drwho8＠gmail.com

On Wed, Jan 9, 2013 at 2:34 PM, <sampsa at mac.com> wrote: Anyone have one of these handy - the one on RHESUS is corrupted.. sampsa Hello! It is? When did that happen? And how? ----- Gregg C Levine gregg.drwho8 at gmail.com "This signature fought the Time Wars, time and again."

12 years, 11 months

MOP vs. Cisco, was Re: [HECnet] _PROVISIONAL_ map of HECnet, courtesy largely of Brian H.

by mcguire＠neurotica.com

On 01/09/2013 01:52 PM, Cory Smelosky wrote: Get a Cisco. It's not like they're tough to find, or very expensive. And you'll use it essentially forever. (because it will last that long!) I've got this 4700 sitting here collecting dust. Now that I have the 1841, 1811w and 2851 I seriously doubt I'll ever touch the 4700 again. Come get it. :) Where would I need to go? ;) Easton, PA. If you aren't familiar with the area, about half way betten NYC and Philly. Dave's gonna be heading my way soon, perhaps he could pick it up and bring it here to me? It'd be easier than me going there. Uh...that's like three hours' drive in the opposite direction, one way. -Dave -- Dave McGuire, AK4HZ New Kensington, PA

12 years, 11 months

HECnet performance....

by roll＠Stupi.SE

Two files, routers.csv that is basically the output of a walk of SHOW KNO CIRC: <fromname>,<fromarea>,<fromnode>,<fromcirc>,<toname>,<toarea>,<tonode>,<tocirc> Put cost on both sides in there we have a tool that can figure out path from A to B and from B to A. So how do I represent a LAN in your notation? (Psevdo node?) -P e.g.: CTAKAH,62,637,QNA-0,A1RTR,1,1023,UNKNOWN MIM,1,13,UNA-0,BENDER,12,2,UNKNOWN GORVAX,8,400,QNA-0,BENDER,12,2,UNKNOWN second file, end_nodes.csv (basically SHOW ADJ NODES): routername,routerarea,endptname,endptarea,endptnode e.g.: GORVAX,8,400,RHESUS,8,403 CTAKAH,62,637,COPOKA,62,4 sampsa On 9 Jan 2013, at 21:44, Ian McLaughlin <ian at platinum.net> wrote: On 2013-01-09, at 11:40 AM, sampsa at mac.com wrote: The output format of the mapper is very simple, and we plan to run it like once a week, max. So if people in non-auto-mappable areas just send me their info in the relevant format, I can use that to complete the map. Just tell us the format, and it will be done :) Ian

12 years, 11 months

HECnet performance....

by Paul_Koning＠Dell.com

On Jan 9, 2013, at 9:57 PM, Peter Lothberg wrote: True. DECnet is a private network technology, so the assumption is that it= can rely on correct management of the routers. And MTU size is one of the= things assumed to be done right. DEC's network for a long time used 576 a= s its MTU; I would assume even a 2020 can be set that way, how else could s= uch a node have existed on the DEC Easynet? paul 2020 can only do three hundred something, my memory fails on the exact number. Maybe it ended up being 376. It's not a problem as long as it's END NODE, decnet will negotiate the smaller numer. The doc said that it only suports ONE serial interface.... --P That makes sense, indeed for an end node the small MTU is no issue (other than the performance impact). That may be how the 2020 people got away with that implementation. paul

12 years, 11 months

HECnet performance....

by roll＠Stupi.SE

True. DECnet is a private network technology, so the assumption is that it= can rely on correct management of the routers. And MTU size is one of the= things assumed to be done right. DEC's network for a long time used 576 a= s its MTU; I would assume even a 2020 can be set that way, how else could s= uch a node have existed on the DEC Easynet? paul 2020 can only do three hundred something, my memory fails on the exact number. Maybe it ended up being 376. It's not a problem as long as it's END NODE, decnet will negotiate the smaller numer. The doc said that it only suports ONE serial interface.... --P

12 years, 11 months

HECnet performance....

by sampsa＠mac.com

Two files, routers.csv that is basically the output of a walk of SHOW KNO CIRC: <fromname>,<fromarea>,<fromnode>,<fromcirc>,<toname>,<toarea>,<tonode>,<tocirc> e.g.: CTAKAH,62,637,QNA-0,A1RTR,1,1023,UNKNOWN MIM,1,13,UNA-0,BENDER,12,2,UNKNOWN GORVAX,8,400,QNA-0,BENDER,12,2,UNKNOWN second file, end_nodes.csv (basically SHOW ADJ NODES): routername,routerarea,endptname,endptarea,endptnode e.g.: GORVAX,8,400,RHESUS,8,403 CTAKAH,62,637,COPOKA,62,4 sampsa On 9 Jan 2013, at 21:44, Ian McLaughlin <ian at platinum.net> wrote: On 2013-01-09, at 11:40 AM, sampsa at mac.com wrote: The output format of the mapper is very simple, and we plan to run it like once a week, max. So if people in non-auto-mappable areas just send me their info in the relevant format, I can use that to complete the map. Just tell us the format, and it will be done :) Ian

12 years, 11 months

HECnet performance....

by roll＠Stupi.SE

This is getting interesting, but I only have DC PSU's on my personal "Lab" GSR and don't have any DC power source.. What GSR model? (There are AC supplies that fit in the same space as the DC..) (where are you located) -P

12 years, 11 months

HECnet performance....

by ian＠platinum.net

On 2013-01-09, at 11:40 AM, sampsa at mac.com wrote: The output format of the mapper is very simple, and we plan to run it like once a week, max. So if people in non-auto-mappable areas just send me their info in the relevant format, I can use that to complete the map. Just tell us the format, and it will be done :) Ian

12 years, 11 months

VMS 8.3 / 8.4 AXP installer ISO?

by mcguire＠neurotica.com

On 01/09/2013 02:34 PM, sampsa at mac.com wrote: Anyone have one of these handy - the one on RHESUS is corrupted.. http://www.neurotica.com/misc/ALPHAF084.IMG (I'm pretty sure that's the right file) Please let me know when you have it so I can remove it from the server. -Dave -- Dave McGuire, AK4HZ New Kensington, PA

12 years, 11 months

HECnet performance....

by sampsa＠mac.com

The output format of the mapper is very simple, and we plan to run it like once a week, max. So if people in non-auto-mappable areas just send me their info in the relevant format, I can use that to complete the map. sampsa On 9 Jan 2013, at 21:16, Johnny Billquist <bqt at softjar.se> wrote: On 2013-01-09 20:10, Peter Lothberg wrote: solution. Be it Ciscos, Multinet on VMS, or Rob's user level router... Do ROB.s user level router do the upper layers, NML? -P (I;m thinking solving the problem with cisco's that don't respond to "Tell".) Nope. Same issue as with the Ciscos... I think we need some other kind of solution than a pure automated mapper in order to figure things out, although more than currently is done through NML could probably be done. Johnny

12 years, 11 months

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

HECnet