HECnet

hecnet@lists.dfupdate.se

10 participants
15598 discussions

by sampsa＠mac.com

Bob, I've been messing with my MULTINET setup, so have seemed to have lost my link from GORVAX to you. Any chance you can reboot it to see if the link comes back up? Sampsa On 4 Jan 2010, at 16:26, Bob Armstrong wrote: ... with a new DSL modem installed. Only the links to DUSTY and STUPI came up - I don't know what happened to everybody else. Bob

15 years, 11 months

CHARON is back up...

by sampsa＠mac.com

Bob, I've been messing with my MULTINET setup on my side, can you still connect CHARON to GORVAX? Sampsa On 4 Jan 2010, at 16:26, Bob Armstrong wrote: ... with a new DSL modem installed. Only the links to DUSTY and STUPI came up - I don't know what happened to everybody else. Bob

15 years, 11 months

hecnet.eu

by mark＠wickensonline.co.uk

Hi Guys, http://hecnet.eu is up and running - not much up there, but there is more to come! Johnny - can I duplicate your information on this site? It's running on an OpenVMS box connected to hecnet, the site is generated using the utility asctohtm to encourage you guys to make a contribution. Asctohtm runs on the VAX and can process very simply formatted ASCII into a nice looking webpage - perfect for adding content by using a VAX/PDP box and then copying it via hecnet onto the target. I'd also like to get a script running to determine the active state of the network, and in the long run a bit of client site charting to produce a network diagram. In the first instance I'd like email suggestions of content please (or you can email me actual content). The idea in the long run is to create a batch job that will scan the decnet default directory and pickup contributions to put on the wall by automatically converting the ascii files into HTML. I'd also like to create an online tutorial/faq to walk people through the basic decnet/bridge setup as well as point out any common issues. Lots of ideas in the pipeline - we did talk about issuing @hecnet.eu email address which would automatically get piped through a SMTP gateway - which would also be very nice. It'd also be nice to get some bios & backgrounds on people using hecnet - sometimes even though it's a big network it can feel a bit lonely! Regards, Mark

15 years, 11 months

Active node script

by healyzh＠aracnet.com

At 8:58 AM +0100 5/23/10, Mark Wickens wrote: There was a script running at http://www.avanthar.com:8080/nodes/ that I used to use to get an active node list. Is that script available? I'd like to run a script on my VAXstation that is up 24/7 and connected to hecnet to do that or something similar. hecnet.eu is now pointing to that box and I should have WASD configured up shortly. Regards, Mark Unfortunately two things happened, one is that I lost the powersupply in that box, and I still haven't had time to either swap powersupplies, or XP1000's. The other is that since my XP1000 and VAX are powered off I've come to realize just how much running them 24x7 was costing. :-( I had a pretty good idea what it was costing me in electricity, and as a result had already been thinking of powering it down, but as it turns out it was even more than I realized. The CGI in question requires Perl. I have some data on the box in question that I need in the next month, so I need to get it back up and running. I'll see about recovering the script as well. Zane -- | Zane H. Healy | UNIX Systems Administrator | | healyzh at aracnet.com | OpenVMS Enthusiast | | | Classic Computer Collector | +----------------------------------+----------------------------+ | Empire of the Petal Throne and Traveller Role Playing, | | PDP-10 Emulation and Zane's Computer Museum. | | http://www.aracnet.com/~healyzh/ |

15 years, 11 months

Active node script

by mark＠wickensonline.co.uk

There was a script running at http://www.avanthar.com:8080/nodes/ that I used to use to get an active node list. Is that script available? I'd like to run a script on my VAXstation that is up 24/7 and connected to hecnet to do that or something similar. hecnet.eu is now pointing to that box and I should have WASD configured up shortly. Regards, Mark

15 years, 11 months

DECNet Issue - moving the system disk between two VMS boxes

by hvlems＠zonnet.nl

NETCONFIG pretty much solves all problems... The ethernet interface on a VAXstation 4000 model 60 is recognized by DECnet as ESA0, so you'll see a LINE and a CIRCUIT called ESA-0. The VAXstation 4000 model 90 uses different hardware and the device is known as ISA-0 to DECnet. You can manually create the corresponding LINE and CIRCUIT components with NCP but running NETCONFIG is a lot faster, if not easier ;-) Hans Vlems -----Oorspronkelijk bericht----- Van: owner-hecnet at Update.UU.SE [mailto:owner-hecnet at Update.UU.SE] Namens Mark Wickens Verzonden: zaterdag, mei 2010 11:42 Aan: hecnet at Update.UU.SE Onderwerp: Re: [HECnet] DECNet Issue - moving the system disk between two VMS boxes OK, So in time honoured tradition I solved the problem pretty much by asking the question. I did a NETCONFIG and a reboot and all is fine again. Regards, Mark. Geen virus gevonden in het binnenkomende-bericht. Gecontroleerd door AVG - www.avg.com Versie: 9.0.819 / Virusdatabase: 271.1.1/2889 - datum van uitgifte: 05/22/10 08:26:00

15 years, 11 months

DECNet Issue - moving the system disk between two VMS boxes

by bqt＠softjar.se

Mark Wickens wrote: OK, So in time honoured tradition I solved the problem pretty much by asking the question. I did a NETCONFIG and a reboot and all is fine again. That said, what you needed to fix was basically just the line and circuit configs. In NCP: SHOW KNOWN LINES SHOW KNOWN CIRCUITS You should see configured something that you don't have, and I think you should also see what you do have, which have not been configured. It's not that tricky to change the configuration parameters yourself. Actually, there is very little you need to do. You basically needs to set the state of the line to running, and the same for the circuit. Then it should work. Put that in the permanent database, so it works right at boot time. Might be that there is one or two parameters on the circuit that you might want to fiddle with, but that would be pretty obvious from just starting to fool around. Johnny -- Johnny Billquist || "I'm on a bus || on a psychedelic trip email: bqt at softjar.se || Reading murder books pdp is alive! || tryin' to stay hip" - B. Idol

15 years, 11 months

DECNet Issue - moving the system disk between two VMS boxes

by mark＠wickensonline.co.uk

OK, So in time honoured tradition I solved the problem pretty much by asking the question. I did a NETCONFIG and a reboot and all is fine again. Regards, Mark.

15 years, 11 months

DECNet Issue - moving the system disk between two VMS boxes

by mark＠wickensonline.co.uk

Hi all, The list has been very quiet lately! I've got a problem which hopefully someone can give me some clues on. I think it's due to the fact that I've swapped a system disk between a VAXstation 4000/60 and a VAXstation 4000/90 - and as a result the decnet configuration is not valid. It looks like this is because the network device name is different: $ start/network decnet %SYSGEN-E-NOUNLOAD, driver is not unloadable %SYSGEN-F-DEVACTIVE, device is active %RUN-F-CREPRC, process creation failed -SYSTEM-F-DUPLNAM, duplicate name %DCL-I-SUPERSEDE, previous value of MOM$SYSTEM has been superseded %DCL-I-SUPERSEDE, previous value of MOM$SYSTEM_NOSOFTID has been superseded %DCL-I-SUPERSEDE, previous value of MOM$SYSTEM_SOFTID has been superseded %NCP-W-UNRCMP, Unrecognized component , Line Line = SVA-0 %SYSTEM-W-NOSUCHDEV, no such device available %NCP-W-UNRCMP, Unrecognized component , Circuit Circuit = SVA-0 %NCP-I-NOINFO, No information in database %RUN-F-CREPRC, process creation failed -SYSTEM-F-DUPLNAM, duplicate name Can someone give me some clues as where to look. Cheers, Mark.

15 years, 11 months

CHIMPY / CHIMP swap and update

by sampsa＠mac.com

Gentlemen, I have moved CHIMPY onto the hardware (Alphaserver 4100) that used to run CHIMP - which will eventually be brought up on my other Alphaserver (a mere 800). This means that my main system now has the chunkiest Alpha hardware in my setup, CHIMPY was of course initially installed in an 800 as I simply couldn't use my 4100 in the tiny apartments I lived in at the time. Sampsa

15 years, 12 months

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

HECnet